Racing Stripes

You want the classic dual-stripe look down the hood without paying a paint shop. Racing stripe decals give you that, and they are cut to order in widths and lengths that fit hoods, roofs, fenders and truck beds. This collection covers stripe kits for muscle car restyling, single accent stripes for daily drivers, and full-length rally stripes. Most are sold as pairs so both sides of the vehicle match. Everything here is die-cut vinyl, not printed, so the color runs through the material and edges stay crisp. Pick the width that matches your panel, choose a finish, and install it in your driveway with basic tools.

What You'll Find in This Collection

This collection includes dual racing stripes, single center stripes, offset stripe pairs, side body stripes, and hood-to-trunk rally stripe kits. Sizes range from short 12-inch fender accents to full-length kits that span 6 to 8 feet. Colors cover the usual black, white, silver and gray plus red, blue and orange.

It suits muscle car owners, truck owners who want a trail-ready look, Jeep and Bronco drivers adding contrast to a flat hood, and anyone restoring a stripe package on an older vehicle. If you need matching accents for other panels, our decal kits collection bundles stripes with door and tailgate graphics.

Choosing Vinyl for Racing Stripes

Two material families matter here. Calendered vinyl is a 6-mil intermediate film best for flat or gently curved panels like truck bedsides and tailgates. Cast vinyl is thinner and more conformable, so it holds down over hood crowns, fender arches and door handles without lifting. For wrap-style stripe work, cast vinyl also comes in matte, gloss and clear finishes.

Finish options include matte, gloss, clear and static cling. A gloss or matte over-laminate adds a smooth top layer over the printed vinyl. Stripe kits made with an air-release liner have micro channels in the adhesive, so bubbles push out instead of trapping under the film.

Sizing and Fit for Racing Stripes

Stripe width is the number buyers get wrong most often. Classic dual stripes run 6 to 10 inches per stripe with a 2 to 4 inch gap between them. Modern muscle cars often use a 12-inch dual setup, while rally stripes on Jeeps and Broncos typically run 8 inches wide per stripe. A single center stripe is usually 4 to 6 inches.

Measure before ordering. For a hood, measure from the front edge to the cowl and subtract 1 inch for a small setback at each end. For full-length stripes, measure hood to trunk or hood to tailgate in one pass and note where the stripes will cross door gaps, since most kits ship as separate panels for each section. On trucks, 6-inch stripes sit well on bedsides between the wheel arches, and 4-inch stripes fit rocker panels without crowding the moldings.

Racing Stripes: Installation and Care

Step 1. Wash the panel with dish soap and water, then wipe with isopropyl alcohol to remove wax and silicone. Work in shade with panel temps between 60 and 80 degrees Fahrenheit.

Step 2. Dry fit the stripes with masking tape, using a hinge strip along one edge. Measure from body lines on both ends so the pair is parallel.

Step 3. Peel the backing, spray the panel and adhesive with slip solution if using wet method, or apply dry with an air-release liner. Squeegee from the center outward.

Step 4. Pop remaining bubbles with a pin, then remove transfer tape by pulling it back on itself at a low angle.

Step 5. Wait 24 to 48 hours before washing. Hand wash only and avoid pressure washing directly at stripe edges, as water can work under the material. Printed vinyl colors may fade with sun exposure over time, so parking in shade when possible can help slow that.

How to Choose Your Stripe Kit

• Curved hood or fenders? Choose cast vinyl with air-release liner.
• Flat panel like a tailgate or bedside? Calendered vinyl works and costs less.
• Vehicle parked outside daily? Add a laminate or choose a film rated for outdoor exposure.
• Want a painted look? Gloss finish in a color close to your accent paint.
• Restoring an original stripe package? Measure the factory width and spacing first, then match the kit.
• Temporary or seasonal look? Shorter fender stripes are easier to remove later.

Related collections

• Car & Truck Decals
• American Flag Decals
• Boat & Marine Decals

Frequently asked questions

Will racing stripes damage my paint when I remove them?

On factory paint in good condition, quality vinyl removes cleanly with heat from a heat gun or hair dryer. Pull slowly at a low angle while warm. Paint that is already failing, repainted panels, or stripes left on for many years can pull loose paint, so test a corner first. Fresh repaints should cure 30 days before applying any decal.

How do I know what stripe width fits my vehicle?

Measure the flat area of your hood or panel with a tape measure, not by eye. Classic duals run 6 to 10 inches per stripe with a 2 to 4 inch gap. If your hood has a raised center spine, measure each flat section separately. When in doubt, tape paper templates of the exact width to the panel and stand back 20 feet to check proportions.

Do the stripes come as one piece or in sections?

Most full-length kits ship as separate panels per body section, for example hood, roof, and trunk, because door gaps and panel breaks interrupt a single stripe. Sectioned kits also ship in smaller boxes and are easier to align one panel at a time. Short hood and fender stripes usually come as one-piece pairs.

Can I install these myself or do I need a shop?

Flat and gently curved panels are realistic DIY work with a squeegee, masking tape, and slip solution. Hood crowns and door handle recesses are harder and favor cast vinyl with an air-release liner. Take your time aligning the first stripe, since the second one is matched to it. Two people help on full-length kits.

Will the color fade or match my paint?

Vinyl colors are close to common paint codes but are not exact paint matches, so order a color sample if matching matters. Our printed vinyl is offered in matte, gloss, static cling and clear finishes, and outdoor use may cause fading over time. Matte finishes tend to show dirt sooner and need more frequent washing.

How long does shipping take within the US?

Stripe decals are cut to order, so processing typically takes a few business days before carrier transit. Kits ship rolled in a tube, not folded, to protect the edges you will align during install. Check the shipping options at checkout for current transit times to your ZIP code.