Shock Stripes Boat Decals | Custom Racing Stripes Set

Description

A set of two shock-style vinyl stripe decals cut to your chosen width from 12 to 48 inches, made for boat owners who want bold graphics on the hull. Available in seven colors with a matte, gloss, or clear finish.

Bold Custom Racing Stripes for Your Boat

Give your hull a sharper attitude with this pair of shock-style stripe decals. Each set includes two matching graphics designed to run along the sides of your boat, adding a clean performance look without the cost of a wrap or paint work. Choose from seven colors and pick the width that fits your vessel, from a subtle 12-inch accent to a full 48-inch statement. The angled shock design reads fast even when the boat is sitting still at the dock. Whether you are dressing up a fishing boat, a runabout, or a pontoon, these stripes are an easy way to make it feel like yours. Order a set for both sides and you have a matched pair ready to apply in one afternoon.

Choose Your Width and Color

Every boat is different, so these decals are cut to order in your choice of width: 12, 18, 24, 30, 36, 42, or 48 inches. Measure the flat area of your hull where you plan to place each stripe before ordering, and keep in mind any curves, rivets, or hardware that could affect placement. Color options cover the most popular hull palettes, so you can match, contrast, or complement your gelcoat. If you want a low-key look, a narrower stripe in a color close to your hull adds just enough definition. For something louder, go wide and pick a high-contrast shade. Both decals in the set are cut from the same material and color lot, so the pair will match side to side.

Vinyl Built for Marine Use

These graphics are printed on cast vinyl, a thin, conformable material that follows the gentle curves of a hull better than thicker films. The inks and laminate stand up to sun, spray, and routine washing with boat soap and a soft cloth. Application is a dry or wet install using the premasked transfer film, and the vinyl removes cleanly with heat when you are ready for a change. Avoid high-pressure washing directly at the edges and do not scrape with hard tools. Because every boat lives in different conditions, we do not promise a specific service life, but with reasonable care the stripes will hold their color and edges through normal seasons on the water.

How to Apply Your Stripe Set

Start with a clean, dry, wax-free surface, ideally in shade so the hull is not hot to the touch. Position each decal with masking tape before peeling any backing, and step back to check alignment from a distance. Use a squeegee or application card to press the graphic down from the center outward, working air toward the edges. If you choose a wet install, a slip solution lets you slide the decal into final position before squeegeeing out the liquid. Wait a full day before launching so the adhesive bonds fully. Full instructions ship with every set, and if anything is unclear, message us before you apply and we will walk you through it.

What you get

• Set of 2 matching shock-style stripe decals, one for each side of your boat
• Seven color options to match or contrast your hull
• Cut to your chosen width: 12, 18, 24, 30, 36, 42, or 48 inches
• Cast vinyl with matte, gloss, or clear finish options
• Premasked with transfer film for easier alignment and application
• Printed to order in the USA by LEO Sticker
• Removable with heat when you want to change your look

Specifications

Frequently asked questions

How do I pick the right width for my boat?

Measure the flat section of hull where you want each stripe to sit, and choose the width that fits within that space with room to spare around curves and hardware. If you are between sizes, the smaller option is usually easier to apply.

Will these stripes work on curved hull sections?

Yes. The cast vinyl is thin and conformable, and the shock-stripe design is cut in sections that flex around gentle hull curves. Very tight compound curves are harder, so aim for the flattest area you can.

Can I remove the decals later?

Yes. Warm the vinyl with a heat gun or hair dryer on low and peel slowly. Any remaining adhesive can be cleaned off with a citrus-based adhesive remover. We cannot promise the gelcoat condition underneath, so test in a small area first.