Model X Decals

The Tesla Model X has one of the most recognizable silhouettes on the road, and its long doors and tall rear liftgate give decal placement options that most crossovers do not. Owners typically look for decals that accent the falcon wing doors, dress up the rear liftgate, or add subtle striping along the lower body. Because the Model X has a smooth, mostly flat paint surface with minimal trim interruptions, vinyl graphics sit cleanly and read well from a distance. Common requests include door accents, rear window lettering, side skirt stripes, and small badges near the front fenders. This page covers where Model X owners usually place decals, how to size them, and what to know before installing on this body style.

Popular Decal Placements on the Model X

The Model X offers several panels that work well for vinyl. The most requested placements are:

• Falcon wing door accents: graphics that run along the lower edge of the rear doors, visible whether the doors are up or closed.
• Rear liftgate: a large, flat area suited to text, logos, or horizontal designs below the rear glass.
• Front doors and fenders: mid-size decals, stripes, or small badges.
• Lower rocker panel area: thin striping that visually lowers the stance.
• Rear glass: lettering or simple shapes placed where defroster lines will not interfere.

Sizing Guidance for Model X Panels

Panel dimensions vary by configuration, so measure your own vehicle before ordering. As general starting points, falcon wing door accents are commonly ordered in the 20 to 36 inch range for width. Rear liftgate graphics often fall between 24 and 48 inches wide, depending on how much of the panel you want to cover. Front door decals are frequently in the 8 to 18 inch range, and rocker panel stripes typically run 40 to 70 inches per side. Width is usually the limiting dimension, so measure the flat area you want the decal to occupy and leave at least an inch of clearance on each side to avoid wrapping over edges or trim gaps.

Materials for Model X Body Panels

The Model X has painted aluminum panels, so standard exterior-grade vinyl works well. Choose a cast vinyl for pieces that need to conform over curves such as door handle recesses or the lower door edges, since cast film stretches without distorting the printed graphic. Calendered vinyl is a lower-cost option for flat areas like the liftgate, though it is generally thicker and less forgiving on compound curves. A matte or gloss laminate layer adds protection against car washes and sun exposure. If you plan to apply vinyl near the rear glass, avoid placing opaque graphics where they could block the rearview camera view.

Installation and Care for Tesla Model X Decals

Before installing, wash the panel thoroughly and remove any wax or sealant with isopropyl alcohol. Work in moderate temperatures and out of direct sun. A few Model X specific points:

• For falcon wing door accents, install with the doors closed and use the door seams as your alignment reference.
• Keep decals clear of the door edge gaps so the film is not stressed when the doors open upward.
• On the liftgate, avoid covering the badge area unless you plan to remove or work around it.
• Use the wet application method for large pieces so you can reposition before squeegeeing.

Related collections

Frequently asked questions

Will decals damage the paint on my Model X?

Quality exterior vinyl applied to clean, factory-cured paint and removed gently with heat typically comes off without residue. Avoid installing on repainted panels that have not fully cured, and avoid leaving decals on for many years in harsh sun before removal. Warm the film with a hair dryer and peel slowly at a low angle.

Can I put decals on the falcon wing doors?

Yes. The lower door panels are a popular spot. Install with the doors closed, keep the graphic inside the panel edges, and do not bridge the door seams. When the doors raise, the decal moves with the door panel and stays intact as long as the film is not stressed across a gap.

How do I know what size decal to order?

Measure the specific panel on your own vehicle with a tape measure, since dimensions vary by configuration and any accessories you may have added. Note the width of the flat area, subtract an inch of clearance on each side, and compare that number to the listed decal size before ordering.

Do decals interfere with the rear camera or sensors?

Vinyl on painted panels generally does not affect sensors, but avoid placing opaque graphics over the rear camera lens area or directly over ultrasonic sensor locations on the bumpers. If a decal needs to cross a sensor zone, cut a relief hole or trim around it during installation.