Subaru WRX Decals

The Subaru WRX is a compact performance sedan with a wide rear wing on most versions, a short rear deck and pronounced fender flares, and owners tend to shop for decals that work with those shapes. Common requests include side graphics that follow the lower door line, rally-inspired stripe sets, small badge-style decals for the fenders or quarter panels, and subtle accents for the rear wing or trunk lid. Because the WRX body is smaller than a full size sedan, many graphics designed for larger cars run long and need to be scaled down. This page covers placement options, sizing ranges, vinyl choices and installation tips specific to this body style so you can order with confidence.

Popular Decal Placements on the WRX

WRX owners usually place decals in a handful of spots that suit the body lines.

• Front fenders and front doors: small side graphics or badge style decals that sit between the wheel arch and the door handle line.
• Rear quarter panels: diagonal stripes or short accent graphics that follow the flare toward the taillight.
• Trunk lid and rear wing: thin stripes on the wing supports or a small decal on the trunk surface between the wing legs.
• Rear glass: a single width banner decal, a popular spot for this model.
• Rockers and lower doors: two tone lower graphics that break at the door seams.

Fit and Sizing for Subaru WRX Decals

Because panel shapes vary between generations and any body modifications change available space, treat these ranges as starting points and measure your own panels before ordering.

• Fender and door accents: roughly 6 to 14 inches wide.
• Rear quarter panel stripes: roughly 12 to 24 inches per side.
• Full side graphics running fender to quarter panel: roughly 40 to 70 inches, cut to break at door seams.
• Trunk lid decals: roughly 10 to 20 inches wide.
• Rear window banners: typically sized to the glass width, commonly 40 to 55 inches.

Always measure the flat area you want to cover, not the total panel, and note any moldings, badges or camera housings in the way.

Materials for WRX Panels

The WRX uses painted steel body panels, glass and, on many versions, a composite rear wing, so material choice matters.

• Cast vinyl conforms better over curves such as fender flares and the rear wing supports.
• Calendered vinyl works fine on flat door and trunk surfaces and is usually the lower cost option.
• For rear glass banners, look for vinyl rated for glass application and check local tint and obstruction laws before applying.
• A matte or gloss laminate can be added to printed graphics to match the surrounding paint texture.

Installation and Care for Subaru WRX Decals

Installation on the WRX has a few body specific considerations.

• Clean door seams and the crease lines along the flares with a mild solvent before applying, since wax buildup in these areas causes edge lift.
• For multi panel side graphics, align the design at the door seam first, then work outward so the break stays level.
• On the rear wing, apply in warm conditions and use heat to help the vinyl wrap the support legs without creasing.
• Quarter panel decals near the fuel filler need the filler door opened during fitting, and the decal should be trimmed or positioned to clear its edge.
• Keep decals clear of the rear camera and third brake light areas on the trunk and glass.

Related collections

Frequently asked questions

Will a side decal set fit every WRX generation?

Not automatically. Panel lengths and door seam positions differ between generations, so a set cut for one body may run long or short on another. Measure the flat area on your own doors and quarter panels, then compare those numbers to the decal dimensions listed before ordering. Sellers can often trim a design to your measurements on request.

Can I put a decal over the rear wing?

Yes, thin stripes and small accents work on the wing surface and support legs. Use a conformable cast vinyl and apply with heat so the material follows the curved supports without wrinkling. Keep the decal clear of any third brake light or washer housing, and avoid wrapping the vinyl under sharp bottom edges where it can peel.

How do I apply a decal near the fuel filler door?

Open the filler door before positioning the decal so you can see the exact boundary. Place the decal so its edge stops short of the door gap, or trim a relief notch at the opening. If vinyl bridges the gap, the door seal can lift the edge over time and the decal will need patching or replacement.

Do decals damage the paint when removed?

Quality vinyl removed within its rated outdoor life, using heat and slow peeling, generally comes off painted panels without issue. Risk increases with age, sun exposure or repainted panels. Warm the decal with a hair dryer or heat gun on low, pull at a shallow angle, and clean residue with a citrus based adhesive remover.