American Flag Tailgate Decal Kit for Ram Trucks

Description

A matte American flag tailgate decal kit printed on Cast Vinyl, made for Ram truck owners who want a clean flag Graphic across the tailgate. Available in 4, 8, 12 or 18 inch decal sizes.

American Flag Design for Your Ram Tailgate

This decal kit lays out a distressed-free American flag Graphic sized to sit across the flat panel of a Ram tailgate. The kit arrives as a multi-piece set so you can position each stripe and the canton yourself, which gives you control over the final look instead of forcing one fixed layout. The flag artwork is printed at high resolution with a full red, white and blue palette. Whether you drive your truck to the job site or keep it clean for weekend shows, the flag reads clearly from a distance without looking like a busy wrap. It is a straightforward way to add a patriotic touch that matches the rest of our ram & dodge durango decals collection.

Matte Cast Vinyl That Blends Into the Paint

Each piece is cut from matte Cast Vinyl, so the decal has a flat, non-shiny surface that sits close to the paint and reads like a printed Graphic rather than a sticker. Cast Vinyl is thin and conformable, which helps it follow the gentle contours and body lines of a tailgate without lifting at the edges. The matte finish also cuts glare, so the flag stays visible in direct sun instead of washing out. Application is a standard peel-and-stick process with transfer tape holding the pieces in alignment until you squeegee them down. One decal size fits most tailgate widths when centered, and smaller sizes work well on toolboxes, windows or bed covers.

Choosing Between 4, 8, 12 and 18 Inch Decal Sizes

The kit comes in four decal sizes: 4, 8, 12 or 18 inches. The 18 inch size is the popular pick for a full-width flag across a truck tailgate, while the 12 inch size suits smaller tailgates or a centered accent. The 8 inch size works well on rear windows, toolboxes and trailer doors, and the 4 inch size is handy for mirrors, cooler lids or laptop covers. Measure the flat area where you plan to apply the kit before ordering, and remember to leave a little margin on each side so the flag does not run into trim lines or Graphic lettering. Every size uses the same artwork and the same matte Cast Vinyl.

Applying and Caring for Your Flag Decal Kit

Start with a clean, dry tailgate; wash off wax and dust, then wipe the area with isopropyl alcohol and let it dry fully. Warm the surface slightly if you are working in cool weather, peel the backing, and use the transfer tape to place each piece. Work from the center outward with a squeegee or credit card to push air out to the edges, then pull the tape back on itself at a low angle. Avoid washing the truck for the first day or two so the adhesive sets. After that, hand washing is fine; just skip high-pressure sprays directly on the decal edges. If you ever want to remove it, warm it with a hair dryer and peel slowly.

What you get

• Multi-piece American flag decal kit for truck tailgates
• Printed on matte Cast Vinyl with a flat, low-glare finish
• Available in 4, 8, 12 or 18 inch decal sizes
• Peel-and-stick application with transfer tape for alignment
• Conformable vinyl follows tailgate contours and body lines
• Works on tailgates, toolboxes, windows and bed covers
• Removable with heat when you are ready for a change

Specifications

Frequently asked questions

Will this kit fit my truck's tailgate?

The kit is sold by decal size, not by vehicle model, so it is not a model-specific fitment. The 18 inch size is a common choice for truck tailgates, but we recommend measuring your flat tailgate area first and comparing it to the 4, 8, 12 or 18 inch options.

Can I apply this in cold weather?

Yes, though vinyl applies best above about 60F. In cooler weather, park the truck in a garage or use a hair dryer to warm both the surface and the decal slightly before placing it, and take your time squeegeeing from the center outward.

Can I take the flag decal off later?

Yes. Warm the decal with a hair dryer and peel it back slowly at a low angle. Any remaining adhesive can be cleaned off with isopropyl alcohol. Removal works best when the decal has not been baked on by years of direct heat.

Is this an official brand product?

Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.