Matte Black Stripe Decal Kit for Model 3 | LEO Sticker

Description

A matte black vinyl stripe decal kit cut to complement the Tesla Model 3 body line. For owners who want a clean, custom look without paint or permanent modification.

A Stripe Kit Cut for the Model 3 Silhouette

This decal kit was designed with the Tesla Model 3 in mind, following the smooth, unbroken surfaces that define the car. The matte black stripes lay along the hood and body lines where a painted racing stripe would go, giving the car a lower, more grounded stance. Because the kit is pre-cut for the Model 3's panel geometry, you get clean edges without needing to trim on the car. Not affiliated with or endorsed by the manufacturer. Each stripe is cut from Cast Vinyl in a matte black finish, so it reads as a flat, painted-on look rather than a shiny sticker, which is exactly what most owners are after when they for Tesla decals in this style.

Matte Black That Reads Like Paint

The matte finish is the whole point of this kit. It absorbs light instead of reflecting it, so the stripes blend with flat trim, window surrounds, and dark wheels rather than fighting them. On a white, silver, red, or blue Model 3, the contrast is sharp and Graphic. On a black car, the stripes create a subtle tonal shift that reads as texture. The vinyl is thin and conformable, so it follows the gentle curves of the hood and doors without lifting at the edges. There is no gloss layer, no shine, and no texture, just a uniform flat black that holds its color through sun, rain, and car washes when applied to a clean surface.

Choose Your Decal Size: 4, 8, 12 or 18 Inches

The kit is offered in four decal sizes so you can dial in the look you want. The 4 inch stripes give a slim, understated accent line, while 8 inch stripes are the most popular middle ground, wide enough to read clearly from across a parking lot. The 12 inch option makes a bolder statement, and the 18 inch stripes create a wide dual-stripe layout that covers serious real estate on the hood. All four sizes use the same pre-cut layout and the same matte black Cast Vinyl, so the only decision is how much visual weight you want. If you are unsure, measure the width of your hood between the body lines before ordering.

Installation in an Afternoon

Application is a wet-install process, which gives you time to slide each stripe into position before it grabs. Clean the paint with isopropyl alcohol, mist the surface with slip solution, place the stripe, squeegee out the liquid, and let it set before removing the transfer tape. The vinyl is forgiving during positioning and can be lifted and repositioned while wet. Work in shade on a cool panel, and avoid applying in direct sun or extreme cold. Full instructions are included in the kit. When you want to remove the stripes later, warm them gently with a hair dryer and peel slowly, they come off without leaving residue on well-maintained paint.

What you get

• Pre-cut stripe layout designed around the Tesla Model 3 body lines
• Matte black finish that reads as flat paint, not a shiny sticker
• Cut from Cast Vinyl that conforms to gentle panel curves
• Available in 4, 8, 12 or 18 inch decal sizes
• Wet-install application with repositionable placement
• Removable with gentle heat without leaving residue
• Includes illustrated installation instructions

Specifications

Frequently asked questions

Will these stripes fit any Tesla Model 3 year?

The kit is designed around the Model 3 body line, which has stayed consistent across model years. Because it is a wet-install vinyl application rather than a rigid part, minor panel differences are not an issue. Not affiliated with or endorsed by the manufacturer.

Which decal size should I choose?

The 8 inch size is the most common choice for a classic dual-stripe look. Choose 4 inch for a subtle accent, 12 inch for a bolder layout, or 18 inch if you want wide stripes with maximum coverage. Measuring your hood between the body lines before ordering helps you visualize the result.

Can I wash my car after applying the stripes?

Yes. Once the vinyl has fully adhered, hand washing and touchless car washes are fine. Avoid high-pressure spray directly at the stripe edges and avoid waxing over the decals, as wax buildup can create a visible edge line.