RV & Camper Decals

A faded stripe panel or a peeled graphic on the side of a travel trailer usually means one thing: it is time to replace it. This collection gathers decals sized and shaped for RV exterior surfaces, from large wall graphics and stripe segments to smaller door badges, window decals and wheel-arch accents. Every decal here is cut from vinyl meant to hold up through highway speeds, road grime and long seasons of sun. Whether you are restoring a vintage motorhome, covering damage on a fifth wheel, or adding a personal touch to a new camper, you will find graphics engineered for the flat aluminum and FRP panels and curved gelcoat surfaces that make up a modern RV.

What RV & Camper Decals Includes

This collection covers exterior and window decals for Class A, Class C and Class B motorhomes, travel trailers, fifth wheels, truck campers and pop-ups. That includes full-width stripe decals, panel accents, entry-door graphics, clearance-light trim pieces, rear-wall murals and smaller window decals for the cab or galley glass.

The audience is broad on purpose. Full-timers replacing sun-damaged OEM graphics can match a color and size. Weekend campers can add a single accent piece. Vintage trailer restorers can source period-style scripts and badges. If you drive it or tow it to a campsite, it belongs here.

Vinyl Types and Finishes

Two vinyl families do most of the work on RV exteriors, and choosing between them matters more than the artwork itself.

• Calendered vinyl is a 6 mil intermediate film with a solvent adhesive. It is the standard choice for flat sidewalls, rear panels and stripe runs. It handles sun and rain well at a lower cost per square foot.
• Cast vinyl is thinner and conforms to compound curves. Use it around wheel arches, curved front caps, molded corners and riveted panels where a thicker film would lift or wrinkle.
• Air-release liner on premium films lets trapped air escape through micro channels during installation. This is the feature to look for on large graphics, because bubbles are the number one cause of a redo.
• Overlaminate, usually a gloss or matte clear, adds protection against fading and abrasion. A gloss laminate keeps colors looking wet and deep. Matte cuts glare on bright days. It is best kept to doors and window areas rather than full walls.

Sizing and Placement for RV & Camper Decals

Measure the RV panel, not the old decal. Old graphics shrink and fade, so matching them directly often produces a gap or overlap.

• Stripe segments: most OEM stripe packages run 4 to 12 inches tall. Measure the full horizontal run and order segments with a few inches of overlap at seams.
• Wall graphics and murals: common sizes range from 24 x 36 inches up to 48 x 96 inches. On a 96 inch tall sidewall, plan for at least 12 inches of clearance above the lower trim and below the window line.
• Door decals: entry doors on travel trailers typically offer a 20 x 30 inch flat area. Keep graphics under 18 x 26 inches to clear the handle and window cutout.
• Window decals: order 6 to 12 inch pieces for cab windows and 12 to 18 inch pieces for galley glass, always facing outward.
• Wheel arch accents: measure the arch circumference plus 4 inches to wrap the leading edge.

Applying and Caring for RV & Camper Decals

A clean, warm surface is 90 percent of the job. Follow these steps in order.

• Step 1: Park the RV in shade and let the surface reach at least 60 degrees F. Cold gelcoat refuses adhesive.
• Step 2: Wash with dish soap and water, then wipe with isopropyl alcohol to remove wax and silicone.
• Step 3: Remove old decal residue with a plastic razor scraper and adhesive remover, then re-clean with alcohol.
• Step 4: Position with masking tape hinges at the top. Peel the backing a few inches at a time.
• Step 5: Squeegee from the center outward with firm, overlapping strokes. On large pieces, use the air-release liner and slow pulls.
• Step 6: Remove transfer tape slowly, pulling back on itself at a flat angle.
• Care: Wash with mild soap and a soft brush. Skip pressure washers at close range and avoid petroleum-based waxes over matte finishes.

Choosing the Right RV & Camper Decals

Work through this short list before ordering and you will land on the right product.

• Flat or curved surface? Flat panel, choose calendered. Curved cap or arch, choose cast with air-release.
• Full replacement or accent? Full stripe replacement means ordering matched segments. An accent piece can be any single decal you like.
• How long will you keep the RV? Keeping it five years or more justifies cast vinyl plus laminate. Selling sooner, calendered alone is fine.
• Where does it go? High-sun walls may show print wear over time. Door and window pieces are fine as-is.
• Need a match? Measure the old graphic and note the color code on its backing if any survived.

Related collections

• Car & Truck Decals
• American Flag Decals
• Boat & Marine Decals

Frequently asked questions

Will these decals survive winter storage and highway driving?

Yes, when installed correctly on a cleaned surface. Calendered and cast vinyl films used here are rated for outdoor exposure, rain, road spray and sustained highway speeds. Laminate adds abrasion resistance against grit. The weak point is almost always surface prep, not the film, so remove all wax and old adhesive before applying.

Can I match the original stripe color on my older trailer?

Many popular stripe colors from major RV manufacturers are close to standard vinyl colors, but exact OEM matches are not always available. Measure the old stripe height and note the color. If a listing shows a color name, compare it against a physical color chart or the old decal itself in daylight before ordering.

Do I need cast vinyl or is calendered enough?

Calendered vinyl works well on flat aluminum and FRP sidewalls, rear walls and straight stripe runs. Cast vinyl is the better choice for curved front caps, wheel arches, molded corners and riveted panels because it stretches and conforms without lifting. If your surface curves in two directions, order cast with an air-release liner.

How do I remove the old decals before installing new ones?

Warm the old graphic with a heat gun or hair dryer on medium, then peel slowly at a flat angle. Use a plastic razor scraper for residue and an citrus or solvent adhesive remover for what remains. Finish with isopropyl alcohol before applying anything new. Never use metal blades on gelcoat or FRP, as they scratch permanently.

What temperature is too cold to install?

Most pressure-sensitive adhesives need a surface temperature of at least 60 degrees F to bond properly. Below that, the adhesive stays stiff and the film will not conform. Park the RV in the sun or in a heated garage for a few hours. In cold climates, plan installs for late morning when the wall has warmed, and avoid applying in direct summer heat above 90 degrees F.

Can I order a custom size or custom design for my RV?

Yes. Custom stickers are available through our custom work, and large wall graphics can often be produced to your measurements. Provide the exact panel dimensions, the surface type (flat or curved), and the color reference. For very large graphics, expect them to ship in sections with overlap allowances so you can align seams on the wall.