Tribal Checkered Flag Vinyl Racing Wrap for Cars & Trucks

Description

A tribal flame and checkered flag side graphic set for cars and trucks, solvent-printed on flexible vinyl and offered in widths from 12 to 48 inches. Made for drivers who want a racing look without a full paint job.

Checkered Flag Meets Tribal Flame on Your Vehicle's Side

This side wrap set pairs two classic racing looks in one graphic: the checkered flag pattern and flowing tribal flame accents. The design runs along the side of your car or truck, dressing the doors and lower body panels with a pattern that reads clearly from a distance and at speed. Whether you are building a weekend track car, a show truck, or just want your daily driver to stand out in the parking lot, the checkered blocks and tribal line work deliver a competition-inspired look without the cost of a full paint job. It is a statement piece for anyone who wants their vehicle to say racing, even in stop-and-go traffic.

Choose Your Width from 12 to 48 Inches

Every vehicle side is different, so this wrap set is offered in a range of widths from 12 inches up to 48 inches. Before ordering, measure the flat panel area you plan to cover, from the body line down or across the door, depending on where you want the graphic to sit, and choose the option that matches. A narrower 12-inch width works as an accent stripe along the rocker or lower door, while the wider options can fill most of the side of a truck door or car quarter panel. Each set is produced at the width you select, so an accurate tape-measure reading is the key step before ordering.

Solvent-Printed Vinyl Built for Outdoor Use

The graphic is printed with solvent inks on flexible cast/calendered vinyl film, the standard construction used for vehicle decals and wraps. Solvent printing bonds the ink into the vinyl rather than letting it sit on top, which helps the checkered pattern hold up to sun, rain, and regular driving. The film carries a pressure-sensitive adhesive backing protected by a release liner, and it is cut to shape so the tribal edges and flag blocks arrive ready to place. On flat and gently curved panels the film lays down smoothly; tighter body lines and areas around mirror mounts can be eased into position with a little heat from a heat gun or hair dryer during installation.

Installing the Side Graphic Set

Start with a clean, dry surface: wash the panels, remove any wax with isopropyl alcohol, and let the area dry completely. Position each piece with the liner still in place, holding it up with small strips of tape until the layout looks right. Peel the liner, tack down one edge, and squeegee from the center outward to push air toward the edges, lifting and re-laying any section that traps a bubble. Use gentle heat to stretch the film around door handles, body creases, and wheel arch curves, and trim excess material with a sharp knife along panel gaps. Give the adhesive a day or two to set before washing the vehicle or driving through heavy rain.

What you get

• Tribal flame and checkered flag side graphic designed for cars and trucks
• Available in multiple widths from 12 to 48 inches
• Solvent-printed on flexible cast/calendered vinyl film
• Pressure-sensitive adhesive backing protected by a release liner
• Conforms to gently curved panels; use heat for tighter curves
• Universal fit by measurement, trim to size during installation

Specifications

Frequently asked questions

Will this fit my specific car or truck model?

This is a universal side graphic, not a model-specific kit, so it is not tied to any particular vehicle. Measure the panel area you want to cover, choose the matching width from the 12 to 48 inch options, and trim the film during installation to work around handles, creases, and panel gaps.

How do I pick the right width?

Measure the height of the door or quarter panel area you want the graphic to fill, from the body line down to the rocker or along the lower panel. A 12-inch width works as an accent stripe, while larger widths cover more of the side. If you are between sizes, measure twice and choose the option closest to your panel space.

Can the wrap be removed later?

Yes. Warm the film with a heat gun or hair dryer and peel it back slowly, keeping the heat on the section you are lifting. Any leftover adhesive can be softened with heat and wiped away using isopropyl alcohol or an adhesive remover. How cleanly it comes off depends on the surface condition and how long the graphic has been applied.