Camaro Racing Stripes | 36" Hood Vinyl Decal Kit, Gloss

Description

A gloss-finish Vinyl Decal kit that lays a pair of racing stripes across the hood of your muscle car. Cut to order in your choice of 4, 8, 12 or 18 inch stripe widths.

Camaro Racing Stripes That Follow Your Hood Lines

This decal kit is cut as a matched pair of center stripes designed to run the length of your hood, with clean, straight edges and a consistent gap down the middle. Because the stripes come as separate pieces rather than one oversized sheet, you can position each side independently and dial in the alignment before anything touches paint. The kit works on flat and gently curved hood surfaces, and the gloss finish sits close to the look of a clear-coated paint line, so the stripes read as part of the car rather than a sticker laid on top. Choose the stripe width that matches the look you want, from a slim accent to a bold dual-stripe layout.

Gloss Cast Vinyl Built for Outdoor Use

Each stripe is printed and cut on Cast Vinyl, the conformable film that bends around body contours without lifting at the edges or fighting compound curves. The gloss top layer gives the stripes a wet-look shine that pairs well with factory paint. Cast Vinyl also handles sun, rain, car washes and road spray far better than cheap printed alternatives, holding its color season after season without cracking along the cut line. Application is a standard wet or dry install with transfer tape: mist the surface, float the stripe into place, squeegee out the fluid, and pull the tape. Full step-by-step instructions ship with every kit.

Choosing Your Stripe Width

The kit is sold by stripe width, so you control how aggressive the finished look reads. A 4 inch pair gives a subtle, vintage-leaning accent that leaves plenty of paint showing. The 8 inch option is the most popular middle ground, wide enough to make a statement without overwhelming the hood. A 12 inch pair fills the hood center and suits bigger, modern bodywork. The 18 inch layout is the boldest cut we offer, built for owners who want the stripes to dominate the front of the car. Measure your hood center between the hood creases before ordering so the pair lands where you want it.

Removable, Reversible and Paint-Safe

Because these are decals and not paint, you can change your mind. Warm the vinyl with a hair dryer or heat gun on low and peel it away in one piece, leaving minimal residue that wipes off with an adhesive remover. That makes the kit a good fit for leased vehicles, daily drivers you plan to resell, or anyone who wants the racing stripe look without committing to a body. Prep is simple: wash the hood, remove any wax with isopropyl alcohol, and install at moderate temperature. With basic care, the stripes stay put through weather and washes, and they come off clean when you are ready for a change.

What you get

• Matched pair of gloss racing stripes cut from Cast Vinyl
• Sold in 4, 8, 12 or 18 inch stripe widths
• Conforms to flat and gently curved hood surfaces
• Wet or dry install with included transfer tape
• Printed and cut to order in our US
• Removable with heat, leaving minimal residue
• Step-by-step installation instructions included

Specifications

Frequently asked questions

Will these stripes fit my specific hood?

The kit is sold by stripe width, not by vehicle, so fitment depends on your hood's center width. Measure the flat or gently curved area between the hood creases and compare it to the 4, 8, 12 or 18 inch pair before ordering. Because each stripe is a separate piece, you can trim the ends with a sharp blade for a custom length.

Can I install these myself?

Yes. The stripes ship on transfer tape, and the two-piece design lets you align each side one at a time. A wet install with a spray of soapy water gives you time to reposition before the vinyl locks down. Most customers complete the install in under an hour with a squeegee and a helper for final alignment.

Will the stripes damage my paint when removed?

On original, well-adhered factory paint, warming the vinyl with a hair dryer lets you peel it off in one piece with minimal residue. Any remaining adhesive cleans up with isopropyl alcohol or a dedicated adhesive remover. We do not recommend installing over fresh or repainted surfaces that have not fully cured.

Is this an official brand product?

Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.