Ford F-350 Decals

The Ford F-350 is a heavy duty pickup with broad, flat panels that give decal buyers a lot to work with. Owners of this truck most often look for graphics that fill the wide door surfaces, tailgate lettering, and stripes or lettering that run along the bed sides. Because the F-350 sits taller and has larger panels than a half ton pickup, sizing tends to run bigger, and what fits a smaller truck can look undersized here. Common requests include side stripes, tailgate graphics, hood accents, and door lettering for work trucks. This collection gathers decals suited to the F-350 cab, bed, and tailgate, with guidance on measuring panels before you order so the graphic lands where you want it.

Popular Placement Areas on the F-350

The F-350 body style offers several large surfaces that suit vinyl decals:

• Doors and front fenders: wide panels that hold long racing stripes or lettering.
• Tailgate: a flat vertical surface commonly used for lettering, logos, or a full width graphic.
• Bed sides: long panels above the wheel arches that work well for running stripes.
• Hood: a broad flat area suited to center stripes or accent graphics.
• Rear window: used for smaller lettering or perforured style graphics where offered.

Fit and Sizing for Ford F-350 Decals

Panel dimensions vary by cab configuration, bed length, and any aftermarket body work, so treat the ranges below as starting points, not fixed sizes. Door and bed side decals for a truck this size commonly fall in the 40 to 70 inch range for full length stripes. Tailgate graphics often land between 30 and 60 inches wide, while hood accents typically run 20 to 45 inches. Before ordering, measure the exact panel you plan to apply to, including any body lines, handles, or trim you want the decal to clear. Measure twice and compare against the listed decal dimensions on the product page.

Choosing Vinyl for Ford F-350 Decals

Decals for the F-350 are cut from adhesive vinyl suited to painted truck panels. Matte and gloss finishes are the most common options, and both hold up to routine washing. For a truck that tows, hauls, or spends time on gravel roads, look for a calendered or cast vinyl rated for outdoor use, since bed sides and lower panels take more road debris than upper surfaces. Thicker vinyl can be easier to position on the large flat panels this truck has, while thinner cast vinyl conforms better around door handles and body lines.

How to Install Ford F-350 Decals

Working on a full size heavy duty pickup means dealing with height and reach. Use a step stool or ladder for bed side and hood placements so you can keep even pressure across the decal rather than stretching to reach the top edge. Clean the panel thoroughly, including around door handles and body seams where grit collects. On the tailgate, work with the gate closed and latched so the surface stays aligned. Apply in moderate temperatures out of direct sun, and use a squeegee from the center outward to push air toward the edges. Large stripes on the bed sides are easiest with two people, one holding the decal level while the other smooths it down.

Related collections

Frequently asked questions

What size decal works best on an F-350 tailgate?

Tailgate graphics for a truck this size commonly run 30 to 60 inches wide, but tailgate dimensions vary by bed configuration and any aftermarket liner or handle cover. Measure the flat area of your own tailgate, including clearance around the handle and camera area, then compare that to the decal dimensions listed on the product page before ordering.

Can I apply one long stripe across the doors and bed side?

Yes, continuous stripes are popular on this truck, but they must be measured carefully because door gaps and body lines interrupt the surface. Measure each panel separately, note the gaps, and order the stripe in sections if needed. Applying over a door gap in one piece usually leads to tearing when the door opens.

Will decals hold up on a truck used for towing and hauling?

Vinyl decals rated for outdoor use handle routine washing and weather. Lower bed side panels take more road debris and spray from a trailer, so inspect those edges occasionally. Avoid high pressure washers aimed directly at decal edges, especially near wheel arches, since lifting usually starts where water gets underneath the vinyl.

Do I need two people to install decals on a full size truck?

For large bed side stripes or wide tailgate graphics, two people make the job much easier. One person holds the decal level while the other smooths it from the center outward. Smaller door lettering and hood accents can be installed solo with a squeegee, masking tape hinges, and a step stool so you can reach the top edges without stretching.