By vehicle
By style
By position
Guides
Marine & water
Powersports
Storefront & office
Labels & packaging
Bulk & wholesale
Send your own artwork
Upload your logo or sketch on any product page: we cut it in the width you choose.
Shop
Kids & anime
Sports & fan
Custom stickers
Start here
Your design, our vinyl
Send a sketch or logo, optional upload box sits under the size selector on every product.
Finishes we print
Sizes we cut
12"18"24"36"48"
A set of four hood stripe decals cut from Cast Vinyl, made for Tacoma owners who want a clean racing stripe look without a full wrap. Choose matte, gloss, clear or static cling in four decal sizes.
JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.
A four-piece layout gives you two wide center stripes and two narrower accent stripes, so you can run a classic dual-stripe look down the hood or trim the set down to a single pair. Because each stripe is cut separately, you control the spacing and can follow the hood lines of your truck instead of forcing a one-piece Graphic into place. The tapered cut sits flat over gentle hood contours, and the set is sized to work on first, second and third generation Tacomas as well as other mid-size trucks with similar hood proportions. If you have been browsing toyota racing stripes for a truck rather than a car, this pack is built for that wider, flatter hood surface.
Every set is printed on Cast Vinyl, which conforms to curves better than thicker calendered films and lays down smoothly on a hood. Matte gives a low-sheen, almost painted-on look that hides fingerprints and water spots. Gloss reads like a factory stripe with a wet-look shine. Clear finishes let your paint color show through the stripe Graphic, which works especially well on colored trucks. Static cling uses no adhesive at all, so it peels off clean when you want a temporary look for a show, a trail weekend or a lease vehicle. All four options are cut to the same shape, so the style stays consistent no matter which finish you pick.
The set is offered in four decal sizes: 4, 8, 12 and 18 inches, measured across the widest stripe in the pack. A 4-inch set reads as a subtle pinstripe accent along the hood edge. The 8-inch size is the most popular middle ground for a visible dual-stripe layout. Twelve inches fills more of the hood center for a bolder statement, and 18 inches suits owners who want the stripes to dominate the front end. If you are between sizes, measure the flat area of your hood between the hood creases first, then pick the size that leaves a little breathing room on each side. When in doubt, going one size down keeps the install forgiving.
Start with a clean, dry hood, ideally applied in shade when the surface is cool to the touch. Position each stripe with masking tape as a hinge, check the spacing from both sides of the truck, then peel the backing and squeegee from the center outward to push air toward the edges. Cast Vinyl is forgiving during placement, so you can lift and reposition a stripe if you catch a bubble early. Skip the install on fresh paint that has not fully cured, and avoid high-pressure washers directly on the stripe edges. Static cling versions apply with just water and a squeegee and remove in seconds. One person can install the full set in an afternoon with basic tools.
The set is cut in a tapered shape that suits Tacoma hoods as well as other mid-size trucks with similar proportions. Measure the flat area of your hood and compare it to the decal size you are considering before ordering.
Yes. Because each stripe is a separate decal, you can install only the wide pair, only the narrow pair, or all four. Some owners save the spares for a tailgate or tool box accent.
Matte gives a subtle painted-on look, gloss reads like a factory stripe, clear lets your paint color show through, and static cling is best for a temporary, adhesive-free application.
Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.
4 inch, 8 inch, 12 inch, 18 inch
Your shopping cart is empty
Notifications
