Rattlesnake Adder Truck Tailgate Vinyl Decal, 12-48 in

Description

A printed rattlesnake graphic decal made for truck tailgates, contour cut to the snake's outline with no background panel. Offered in widths from 12 to 48 inches for full tailgate placements, toolboxes, and windows.

A Coiled Rattlesnake Graphic Made for Tailgates

The Adder is a printed rattlesnake graphic laid out to span the flat panel of a truck tailgate. The artwork shows the snake in a coiled, ready-to-strike pose, with scale shading along the body and a raised rattle detail that reads clearly from a distance. Because the design is printed rather than cut from solid vinyl, it can carry the gradients and fine shading that give the snake a fuller look than a single-color silhouette. It is a statement piece for ranch trucks, hunting rigs, and anyone who wants a western edge on the back of their vehicle, and at the smaller widths it also works on toolboxes, trailer doors, and windows.

Solvent-Printed Vinyl, Contour Cut with No Background

Each decal is printed with solvent inks onto vinyl film, the standard construction for vehicle graphics that live outdoors. The inks lay down in fine dots, which is what allows the rattlesnake artwork to hold its gradients and scale shading instead of flattening into solid color. The printed graphic is then contour cut along the snake's outline, so there is no background panel; once installed, you see the snake, not a sticker rectangle. A layer of transfer film is pre-applied over the printed face, which keeps every piece of the cut graphic in position and lets you move the whole design onto the tailgate as one placement. The surface has a printed gloss finish.

Applying the Adder to Your Tailgate

Installation is a dry application done with the transfer film. Start with a clean tailgate: wash off dust and road film, then wipe the area with isopropyl alcohol and let it dry fully. Peel the backing paper away, position the snake where you want it, and press down the center of the graphic first. Work outward with a squeegee or the edge of a card, pushing air toward the edges instead of trapping it under the film. Once the decal is down, peel the transfer film away slowly at a low angle, going back over any spot that lifts with it. Applying in mild weather and out of direct sun gives the vinyl easier working conditions and a cleaner result.

Picking Your Width from 12 to 48 Inches

The decal comes in your choice of width from 12 inches up to 48 inches, and the artwork scales with the size you pick, so the snake keeps the same proportions at every option. Before ordering, measure the flat area of your tailgate between the taillights and any handle or camera trim, then compare that number to the listed widths. A 36 to 48 inch width is the common choice for a full-width tailgate placement, while the 12 to 18 inch sizes suit pickup toolboxes, cooler lids, windows, and trailer doors. If you are placing the snake off-center or on a smaller panel, choose a width that leaves a couple of inches of clearance on each side so the graphic does not run over body lines or trim.

What you get

• Printed rattlesnake graphic designed for truck tailgates
• Available in widths from 12 in to 48 in
• Solvent-printed on vinyl for outdoor display
• Contour cut to the snake's outline with no background panel
• Transfer film pre-applied for one-piece placement
• Printed gloss finish
• Single application; not reusable once removed

Specifications

Frequently asked questions

What width should I order for my tailgate?

Measure the flat area of your tailgate between the taillights and any handle or trim, then pick a decal width equal to or slightly smaller than that measurement. The artwork scales to the width you choose, so the snake keeps the same proportions at every size.

Is this made to fit a specific truck model?

No. The Adder is a universal graphic, not a model-specific kit, so it is not cut around any particular tailgate handle or camera layout. Measuring your own tailgate before ordering is the way to confirm the width you need.

Can I take it off later?

Yes. Warm the decal gently with a hair dryer and peel it up slowly from one end, working in small sections. Any adhesive left behind can be cleaned off with isopropyl alcohol. The decal is a one-time application and is not reusable once removed.