Orca Killer Whale Flame Boat Decals

Orca Killer Whale Flame Decals for Boats, Set of 2

A pair of killer whale decals with flame accents, cut from marine-ready vinyl for boat hulls and transoms. Made for boaters who want bold graphics that hold up on the water.

Free shippingUSA: 5-7 days. International: 10-12 days.

Four finishesMatte, gloss, static cling or clear vinyl.

Made to orderNo returns for change of mind. Damaged orders are refunded or replaced.

Custom artworkUpload a sketch, logo or photo before adding to cart.

Size

Clear

Have your own design? Optional

Upload a logo, sketch or photo

JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.

Description

A pair of killer whale decals with flame accents, cut from marine-ready vinyl for boat hulls and transoms. Made for boaters who want bold graphics that hold up on the water.

Killer Whale Flame Decals Built for Boat Life

This set of two orca decals pairs the unmistakable black-and-white silhouette of a killer whale with trailing flame accents, giving your hull or transom a fast, aggressive look even at the dock. Each decal is printed on cast vinyl and available in matte, gloss, static cling or clear finishes, so you can pick the look that suits your boat. The mirrored pair works on both sides of your boat, or you can run them bow to stern for a wrap-style effect. Choose a width from 12 to 48 inches to match your boat's proportions, from small skiffs to offshore center consoles. If you're browsing flame decals for a marine application, this is one of the few designs made specifically with boaters in mind.

Matte or Gloss Finish, Your Call

Every set is printed to order in your choice of matte or gloss finish. Matte blends into painted gelcoat for a painted-on look and cuts glare on bright days, while gloss adds depth and shine that pops against flat hull colors. Both finishes use the same cast vinyl base, so the choice is purely aesthetic. Prefer something you can remove and reposition season to season? Ask about our static cling option, which applies without adhesive. For a subtle look on tinted surfaces or dark hulls, the clear finish keeps the flame lines visible while letting the underlying color show through. Whatever you pick, the decal die-cuts cleanly to the artwork with no background film to trim.

Sizing the Pair to Your Boat

Widths run from 12 inches up to 48 inches, measured at the widest point of each whale-and-flame graphic. As a rule of thumb, a 12 to 18 inch set suits jon boats, kayaks and personal watercraft; 24 to 30 inches fits most bass boats and bowriders; and 36 to 48 inches makes a statement on offshore hulls, pontoons and cabin cruisers. Because each decal is cut after you order, the artwork scales cleanly rather than stretching, so proportions stay true at every size. Apply one decal per side for symmetry, or stack the pair on a transom for a layered flame effect. If you're between sizes, sizing up slightly usually reads better from a distance on the water.

Applying Your Orca Decals on the Water Side

Application is a dry or wet process with transfer tape, doable by one person in under an hour for most sizes. Start with a clean, wax-free surface, ideally out of direct sun so the vinyl doesn't stretch during positioning. Peel the backing, position the decal, and squeegee from the center outward to push out air and moisture, then remove the transfer tape slowly at a low angle. Full adhesion develops over the first day or two, so avoid high-pressure washing at close range right after installation. When it's time to remove or replace the graphics, warm the vinyl gently and peel it away. Full step-by-step instructions ship with every set.

What you get

Set of 2 mirrored killer whale decals with flame accents
Printed on cast vinyl with our standard inks
Available in matte, gloss, static cling or clear finish
Width options from 12 to 48 inches, scaled without distortion
Die-cut to the artwork with no clear background to trim
Printed to order in our US shop
Includes transfer tape and application instructions

Specifications

Material	Cast vinyl, printed inks
Finish	Matte, gloss, static cling or clear (select at checkout)
Application	Hulls, transoms, boat sides; wet or dry apply with included transfer tape
Set contents	2 mirrored decals, transfer tape, application instructions

Frequently asked questions

Will these decals hold up to salt water and sun exposure?

They are printed on cast vinyl with our standard inks and laminate, the same construction we use across our boat decal line. How they hold up outdoors depends on climate, storage and how the boat is washed, so we don't quote a specific lifespan.

How do I choose between matte and gloss?

Matte gives a painted-on look and reduces glare, which many boaters prefer on lighter hulls. Gloss adds shine and contrast, especially on flat or dark colors. Both use the same vinyl and ink, so it comes down to the look you want.

What size should I order for my boat?

For smaller craft like kayaks and jon boats, 12 to 18 inches works well. Bass boats and runabouts typically look right at 24 to 30 inches, while 36 to 48 inch sets suit larger offshore hulls and pontoons. Measure the flat area where you plan to apply before ordering.