By vehicle
By style
By position
Guides
Marine & water
Powersports
Storefront & office
Labels & packaging
Bulk & wholesale
Send your own artwork
Upload your logo or sketch on any product page: we cut it in the width you choose.
Shop
Kids & anime
Sports & fan
Custom stickers
Start here
Your design, our vinyl
Send a sketch or logo, optional upload box sits under the size selector on every product.
Finishes we print
Sizes we cut
12"18"24"36"48"
A vinyl banner kit sized for the top strip of your Jeep windshield, cut to order in your choice of decal height. For drivers who want a clean, custom look across the glass.
JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.
The top edge of a Jeep windshield is prime real estate, and this decal kit is built for exactly that space. Each banner is cut from durable vinyl and trimmed to your chosen height, so you can run a slim strip along the visor line or a taller band that makes more of a statement. The kit ships as a ready-to-apply set with transfer tape already in place, so you are not piecing together letters or guessing at spacing. Whether you run doors on or off, top up or down, the banner sits flat against the glass and stays put through washes, highway miles, and trail dust. It is a simple way to make a stock Jeep look like yours.
This kit is sold by decal height, with four options to match how bold you want the banner to read. The 4 inch strip keeps things subtle and works well if you want lettering that peeks out above the visors. The 8 inch option is a popular middle ground, wide enough to carry a phrase without eating into your sightline. The 12 inch banner makes the windshield itself part of the design, while the 18 inch option turns the upper glass into a full Graphic band. Before ordering, measure the clear space at the top of your windshield and check your local tint and obstruction laws, since rules on decals over glass vary by state.
Every banner in this kit is printed on professional-grade Cast Vinyl or calendered vinyl, depending on the finish you select. Matte gives the glass a factory-tinted look and cuts glare on bright days. Gloss reads more like paint and catches the light as you drive. Clear finishes let you layer lettering over the view with almost no visible background. Static cling is the pick if you want a banner you can reposition or remove without adhesive, handy for leased vehicles or seasonal use. Whichever you choose, the vinyl is cut and weeded by hand, then masked with application tape so it goes down in one piece.
Installation takes about twenty minutes with basic tools you likely already have. Start with a clean windshield, washed and dried with no wax or rain-repellent residue left behind. Lay the banner in place and hold it with small strips of tape to check alignment before committing. Peel the backing, squeegee from the center outward to push out air, then pull the transfer tape back at a low angle. Work in shade or a garage so the glass is not hot to the touch, and skip applying in freezing weather. Warm the decal gently with a hair dryer if you need it to conform around a curved section of glass, then trim any excess with a sharp blade.
Visibility depends on the height you choose and where you place it. Many states restrict decals above the AS-1 line marked on your windshield. Check your local laws before ordering, and consider a smaller height if you want to keep the full view open.
Yes. Warm the vinyl with a hair dryer and peel it back slowly at a low angle. Any leftover adhesive can be cleaned off with glass cleaner and a plastic scraper. Static cling finishes peel off with no adhesive at all.
The banner is cut as a straight strip, so it works on most flat or gently curved windshields. Measure the width of your windshield's top strip before ordering, and note that very curved glass may need extra care during application.
Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.
4 inch, 8 inch, 12 inch, 18 inch
Your shopping cart is empty
Notifications
