Inflame Skulls Boat Decals, Flame & Skull Marine Vinyl Set

Description

A skull-and-flames vinyl decal set for boat owners who want aggressive graphics on the hull. Printed on marine-ready cast vinyl in your choice of width from 12 to 48 inches.

Skull and Flame Graphics for Your Boat Hull

This Inflame Skulls decal set brings a bold skull-and-flame design to your watercraft. Each set includes mirrored left and right graphics so the artwork lines up on both sides of the hull, with extra pieces sized for transoms, consoles, or storage lids. The artwork is printed in high-resolution detail, from the shading in the skull to the licks of the flame tails, so the design holds up visually whether you choose a smaller 12-inch width for a jon boat or go wide at 48 inches for a center console. The flames trail back toward the stern, giving the boat a sense of motion even at rest on the trailer or dock.

Marine-Grade Cast Vinyl Built for the Water

These boat decals are printed on cast vinyl, the conformable material we use for curved and contoured surfaces. Cast vinyl stretches and compresses around hull curves, chines, and rub rail transitions more readily than thicker films. The printed design is available in our stocked matte, gloss, static cling, and clear vinyl options, printed with inks suited to our standard process. Application is a wet or dry install with transfer tape; the decals can be repositioned during install before final squeegeeing. Once applied, the edges lay flat and the print remains readable with basic care and gentle cleaning.

Finish Options: Matte, Gloss, Clear and Static Cling

Choose the finish that fits your build. Matte gives the artwork a low-sheen, painted-on look that works well on darker hulls and non-skid areas. Gloss adds depth and shine that pops against flat gelcoat. Clear vinyl lets the skull-and-flame design float over your existing hull color, with the print reading as part of the boat itself. Static cling versions apply without adhesive, so you can move the graphics between boats or remove them at season's end without residue. All four finishes use the same artwork and sizing, so the look stays consistent no matter which option you pick.

Sizing and Placement Guide

Sets are sold by overall width, from 12 inches up to 48 inches, measured at the widest span of the main graphic. Measure the flat or gently curved section of hull where you plan to place each piece before ordering, and allow a little clearance from waterlines, registration numbers, and hardware. The mirrored pair works on port and starboard sides, while the smaller accent pieces suit transoms, hatches, and motor cowls. If you boat in cooler climates, install above 50°F for best adhesion. Clean the surface with isopropyl alcohol and let it dry fully before applying.

Installation Tips for a Bubble-Free Application

Start with a clean, dry hull surface free of wax, salt residue, or grease. Wipe the area with isopropyl alcohol and allow it to fully evaporate before positioning your decal. Apply in moderate temperatures, avoiding direct midday sun, so the vinyl adheres evenly. Peel the backing slowly while smoothing the graphic from the center outward using a squeegee or soft card, working air toward the edges. If a bubble appears, lift the nearest edge gently and press the material flat rather than puncturing it. For larger skull and flame pieces, a helper can hold the decal level while you work. Wait at least 48 hours before launching the boat so the adhesive bonds completely to the hull.

Care and Maintenance After Installation

Rinse decals with fresh water after each outing to remove salt and grime that can dull the finish over time. Use a soft cloth or sponge with mild soap, avoiding abrasive pads, stiff brushes, or solvent-based cleaners that may damage the printed surface. When trailering, secure lines and gear so nothing scrapes across the graphics. Wax can be applied around the decals but should not sit on top of them, as buildup along the edges can eventually lift the material. Inspect the edges seasonally and press down any lifting spots promptly. With regular fresh-water rinsing, gentle washing, and careful storage, the flame and skull graphics will keep their color and adhesion through many seasons on the water.

What you get

• Skull-and-flames artwork set with mirrored left and right pieces
• Available in 12, 18, 24, 36, and 48-inch widths
• Printed on conformable marine-ready cast vinyl
• Matte, gloss, static cling and clear printed vinyl finishes
• Four finish choices: matte, gloss, clear, and static cling
• Wet or dry application with transfer tape included
• Accent pieces included for transoms, consoles, and hatches

Specifications

Frequently asked questions

Will these boat decals hold up to salt water and washing?

Yes. The printed vinyl is offered in matte, gloss, static cling, and clear finishes, and it can be used outdoors. Avoid direct high-pressure spray at the edges.

How do I choose the right width?

Measure the widest span of the flat or gently curved hull area where the main decal will sit, then pick the width that fits with a little clearance. The 12-18 inch sizes suit small boats and hatches; 24-48 inch widths fit larger hull sides and consoles.

Can I remove the decals later?

Yes. Warm the decal with a heat gun or hair dryer and peel slowly; adhesive residue can be cleaned with an adhesive remover. Static cling versions remove cleanly with no residue and can be reused.