Feedback Stripes Boat Decal Set of 2

Feedback Stripes Boat Decal Set of 2 | Racing Stripes

A pair of feedback-style stripe decals cut from cast vinyl, made for boat owners who want a racing look on their hull. Choose your width from 12 to 48 inches to fit your boat.

Free shippingUSA: 5-7 days. International: 10-12 days.

Four finishesMatte, gloss, static cling or clear vinyl.

Made to orderNo returns for change of mind. Damaged orders are refunded or replaced.

Custom artworkUpload a sketch, logo or photo before adding to cart.

Size

Clear

Have your own design? Optional

Upload a logo, sketch or photo

JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.

Description

A pair of feedback-style stripe decals cut from cast vinyl, made for boat owners who want a racing look on their hull. Choose your width from 12 to 48 inches to fit your boat.

Give Your Hull a Custom Racing Stripes Look

These feedback stripes bring a clean, performance-inspired look to your boat without the cost of a full wrap or paint work. Each order includes two matching stripe decals, so you can dress up both sides of the hull or run them along the gunwale for a balanced appearance. The design works on fishing boats, runabouts, pontoons and center consoles alike. Because you pick the width, from 12 inches up to 48 inches, you can size the stripes to your boat instead of forcing a one-size decal onto a curved surface. Apply them as a pair, split them up, or trim during installation to create your own layout. It is a simple way to make an older boat look refreshed or a new one feel like yours.

Cast Vinyl Built for Marine Use

We cut these boat graphics from cast vinyl, a thin and flexible film that conforms to the moderate curves found on most hulls and transoms. Cast vinyl lays flatter and conforms more readily than thicker, stiffer films, which matters on a surface that spends its life in sun, spray and humidity. The matte finish keeps the look understated, softening glare on bright days so the stripes read as paint rather than plastic. If you prefer a wetter look, gloss is available at checkout. Both finishes are printed on vinyl suited to outdoor use, so they can go along for salt-air and wake-spray as part of normal boating. Clean the surface, apply the decals, squeegee them down, and they sit flush with the hull rather than an add-on stuck on top of it.

Two Stripe Layouts, One Easy Install

Every set ships as two individual stripe decals with a masking layer on top, so the whole graphic goes down as one piece per side. That means no lining up dozens of separate cuts and no guessing at spacing. Installation is a dry application: peel the backing, position the stripe, and use a squeegee or firm card to press it down while pulling the mask away. On cool days, a little heat from a hair dryer helps the vinyl follow curves near the bow. Full illustrated instructions come in the box. Most boaters finish both sides in under an hour with no special tools. If you make a mistake on placement, the vinyl can be lifted and repositioned before you burnish it down fully.

Sizing, Care and Ordering

Measure the area where you want the stripes before ordering, and compare it against the width options from 12 to 48 inches. The stripe set is designed to be trimmed during installation, so a slightly larger size gives you room to work with. Before applying, wash the hull with soap and water, remove any wax with rubbing alcohol, and let the surface dry completely. After installation, wait about a day before launching so the adhesive sets. For long-term care, rinse the decals when you wash the boat and avoid high-pressure spray directly against the edges. Each set is made to order in our shop, cut after you choose your size and finish, so it arrives fresh and ready for the water.

What you get

Set of 2 matching feedback stripe decals for both sides of your boat
Width options from 12 to 48 inches to fit hulls of different sizes
Cut from cast vinyl that conforms to curved hull surfaces
Available in matte or gloss finish
Dry application with premasked graphics for straightforward installation
Trim-to-fit design lets you customize the layout during install
Made to order in our US shop

Specifications

Material	Cast vinyl
Finish	Matte (gloss available)
Application	Dry application with premask; trim to fit during install
Set contents	2 stripe decals, application mask, illustrated instructions

Frequently asked questions

Will these stripes work on a fiberglass hull?

Yes. Cast vinyl is thin and flexible, so it adheres well to smooth gelcoat and fiberglass. Clean the surface with rubbing alcohol to remove wax before applying.

Can I trim the stripes to fit my boat?

Yes. The decals are designed to be trimmed during installation. Measure your space first, and if you are between sizes, choose the larger width so you have material to work with.

How long should I wait before putting my boat in the water?

We recommend waiting about a day after installation so the adhesive fully bonds before the decals get wet. Rinse with fresh water when you wash the boat to keep the edges secure.