Dragon Tear Hood Decal - 3-Piece Vinyl Set for Cars & Trucks

Description

A three-piece dragon tear decal set printed on vinyl, made for car and truck hoods. Available in widths from 12 to 48 inches so you can size the graphic to your hood.

The Torn-Hood Dragon Effect

This three-piece decal set is built around a classic tear-through design: the artwork reads as a rip torn in the hood, with a dragon revealed in the opening. The three contour-cut pieces layer together so the torn edges and the dragon artwork line up as one graphic once applied. Because the design is printed rather than a simple cut-vinyl shape, the shading along the torn edge and the detail in the dragon artwork come through in full color. It is a bold hood graphic for drivers who want a fantasy-inspired look without painting the hood. The set is made for cars and trucks, and the same pieces can go on any smooth, flat surface, from toolboxes to coolers.

Choosing Your Width: 12 to 48 Inches

The set is offered in a range of widths, from 12 inches up to 48 inches, so the same design can scale from a compact accent to a full-width hood graphic. Before ordering, measure the flat area of your hood between the body lines, seams, or scoop, and choose a width that fits inside that space with room to spare. A 12- to 18-inch width works as a smaller accent near a hood scoop or off to one side, while 30- to 48-inch widths cover more of the hood on trucks and full-size cars. When in doubt, measure twice; a decal that fits the flat panel applies cleaner than one that has to ride over body lines and curves.

Vinyl, Ink, and Cut

Each piece is printed on vinyl decal film using solvent-based inks, the standard method for full-color automotive graphics. The artwork is contour-cut to its shape, so there is no printed background rectangle to hide, only the tear edges and the dragon artwork show once the pieces are down. The back of each piece carries a pressure-sensitive adhesive with a release liner, the same peel-and-stick setup used on standard car decals. Vinyl graphics of this type are made for outdoor use, so rain, washing, and everyday driving are part of the expected environment. Care is simple: hand washing is gentler than pressure washing directly at the edges, and wax around the decal rather than over it.

Putting the Three Pieces Up

Start with a clean hood: wash the area, remove any wax or polish, and let the surface dry completely. Position the largest piece first without removing the liner, using masking tape to hold it and step back to check placement. Once you like the line, peel the liner, lay the piece from one edge, and work outward with a squeegee or credit card to push air out from under the vinyl. Repeat with the remaining pieces, lining them up against the first. Applying in moderate temperatures on a dry day makes the vinyl easier to work with. If a small bubble remains, a tiny pinhole lets the air escape when you press it flat.

What you get

• Three-piece dragon tear decal set for car and truck hoods
• Available in widths from 12 to 48 inches
• Full-color artwork printed with solvent-based inks on vinyl
• Contour-cut pieces with no background film around the design
• Peel-and-stick pressure-sensitive adhesive with release liner
• Tear-through design gives the look of a ripped-open hood
• Also applies to smooth flat surfaces like toolboxes and coolers

Specifications

Frequently asked questions

How do I pick the right width for my hood?

Measure the flat area of your hood between the body lines and seams, then choose a width that fits inside it. The set is offered from 12 to 48 inches wide, so the same design can work as a small accent or a full-width truck hood graphic.

Is this made for a specific vehicle model?

No. The decal is not model-specific and does not depend on any particular hood shape. It applies to any smooth, flat surface large enough for the width you choose, including hoods, toolboxes, coolers, and walls.

How do I remove the decal later?

Warm the vinyl with a hair dryer or heat gun on a low setting and peel slowly from one corner. Leftover adhesive can be cleaned off with an automotive adhesive remover, then wash and wax the area as usual.