Camo Tear Vinyl Decal Kit for Trucks & Trailers

Description

A ripped-camouflage decal kit that adds a torn metal look to pickup trucks, work trucks and semis. Printed on cast vinyl and sold in sets with your choice of width from 12 to 48 inches.

Ripped Camo Truck Graphics That Look Torn, Not Stuck On

This kit creates the illusion of torn sheet metal revealing a camouflage pattern underneath, a style that reads as rugged on pickups, service trucks and semi trailers alike. Each tear is printed with shading and edge detail so the rip looks like it happened in the shop, not on a printer. The panels arrive pre-cut and ready to place, so you can position the tears wherever they suit your bodywork, fenders, hood or trailer sides. Choose a width between 12 and 48 inches depending on how subtle or loud you want the effect to be. It is a straightforward way to give a working vehicle personality without committing to a full wrap.

Matte and Gloss Finishes for a Realistic Camo Decal Kit

The torn-metal effect depends on how light hits the surface, so finish matters. Matte gives the camouflage area a flat, tactical look and keeps the exposed edges reading as raw steel. Gloss adds depth, making the camo pattern pop against the painted panel around it. Both are available at checkout, and both are printed on cast vinyl that conforms to the gentle curves and body lines found on trucks and trailers. If your vehicle sits outside in sun, dust and road grime, either finish cleans up with soap and water. Pick the finish that matches the rest of your build, or mix them across different tears for contrast.

Sizing Guide for Semi Trucks, Trailers and Pickups

Because the kit is sold by width, matching it to your vehicle is simple. A 12 to 18 inch width suits pickup doors, fenders and tailgates where you want a contained tear. Mid sizes around 24 to 30 inches fill a truck bed side or a trailer panel with room to spare. The larger 36 to 48 inch widths are built for semi trailer sides and sleeper cabs, where a small decal would disappear against the scale of the rig. Measure the flat area you want to cover before ordering, and remember you can trim the decal during installation for a custom edge. Every set includes multiple tear pieces so you can balance the design across both sides.

Installing Your Camo Decal Kit in an Afternoon

Installation is a wet-or-dry application using the same basic tools as any vinyl graphic: a spray bottle with soapy water, a squeegee and a sharp blade for trimming. Clean the surface fully and let it dry, then position each tear with the masking tape hinge method before committing. Work from the center outward to push out air and moisture, then remove the transfer tape slowly. Cast vinyl conforms around rivets, seams and gentle body contours on semi trailers, so heat from a hair dryer helps on tighter areas. Park the vehicle out of rain for the first day while the adhesive sets. One careful afternoon gives you a finished look that lasts through regular washing.

What you get

• Torn-metal camo design printed with detailed rip shading and edge highlights
• Sold as a multi-piece kit sized by width, from 12 to 48 inches
• Available in matte or gloss cast vinyl finishes
• Conforms to body lines, rivets and gentle curves on trucks and trailers
• Pre-cut pieces with transfer tape for straightforward positioning
• Wet or dry application with common vinyl install tools
• Fits pickup doors, truck beds, trailer panels and semi trailer sides

Specifications

Frequently asked questions

What width should I order for a semi trailer?

For trailer sides and sleeper cabs, the 36 to 48 inch widths work best because a smaller tear can look lost on a large flat panel. Measure your available space first and remember you can trim the decal during installation.

Can I use these tears on a pickup truck?

Yes. The 12 to 24 inch widths are sized for pickup doors, fenders, tailgates and bed sides. The kit includes multiple pieces so you can place tears on several panels for a balanced look.

Will the decals survive truck washes?

Once the adhesive has fully set, the cast vinyl holds up to normal hand washing and touchless washes. Avoid high-pressure spray directly at the edges of the tear, and skip brush-style washes for the first week after installation.