Tacoma Racing Stripe Kit - Matte Vinyl Decal Set

Description

A matte racing stripe decal kit cut from Cast Vinyl, sized for truck beds, tailgates and body panels. Made for Tacoma owners who want a clean motorsport look without paint.

Matte Racing Stripes That Suit a Working Truck

Gloss stripes can look out of place on a truck that earns its keep. This kit is printed on matte Cast Vinyl, so the stripes read as part of the paint rather than a sticker laid on top of it. The flat finish also hides dust, water spots and light swirls far better than a shiny surface, which matters if your truck lives outside or on job sites. Each stripe is cut clean with no background film, so all you see on the panel is the stripe itself. The kit is built for Tacoma beds, tailgates and side panels, and the matte black tone works against most factory paint colors, from white and silver to darker grays and blues.

Choose Your Decal Size: 4, 8, 12 or 18 Inches

Every truck and every build is different, so this stripe kit is sold in your choice of four decal widths: 4, 8, 12 or 18 inches. Narrower stripes give a subtle, understated line along the bed or tailgate, while the wider cuts make a bolder statement across body panels. Because you pick the width, you can match the stripe to how much clean surface your truck actually has, working around bed rails, Graphic and handle recesses. If you are planning toyota racing stripes across multiple panels, many buyers pair a wider set for the sides with a narrower set for the tailgate. All widths come as a complete left-and-right kit so the layout stays symmetrical.

Cast Vinyl Built for Outdoor Use

These stripes are cut from Cast Vinyl, the conformable grade that bends around gentle curves instead of fighting them. That flexibility matters on truck panels, where slight crowns and body lines would make a stiffer film lift or tent. The vinyl is finished matte, with a permanent adhesive that holds through washes, rain and road spray. Application is a standard wet or dry install with transfer tape: clean the panel, position the stripe, squeegee from the center outward, then peel the carrier. Anyone who has applied decals before can handle this at home with a squeegee and a little patience, and the material repositions during a wet install.

A Weekend Project With a Big Visual Payoff

Painted stripes cost real money and are permanent. This kit gives you a similar look for a fraction of that, installed in an afternoon with tools you likely already own. Lay out both sides before committing, keep the stripes level with a reference line such as a bed rail, and work in shade so the panel is not hot to the touch. If you change your mind later, the vinyl warms off with a heat gun or hair dryer and peels away in one piece, leaving the paint underneath ready for a wash and wax. It is an easy way to make a stock truck look built rather than bought.

What you get

• Matte Cast Vinyl with a flat, low-sheen finish
• Sold in decal widths of 4, 8, 12 or 18 inches
• Complete left and right stripe kit for a symmetrical layout
• Contour-cut with no background film, stripe only
• Conformable material bends around gentle panel curves
• Installs wet or dry with transfer tape and a squeegee
• Removable with heat without leaving residue behind

Specifications

Frequently asked questions

Which stripe width should I choose for my truck?

It depends on the look you want and the space you have. The 4 and 8 inch widths work well for subtle accent lines along the bed or tailgate, while 12 and 18 inch widths make a bolder statement on side panels. Measure your clean panel space before ordering, working around bed rails, Graphic and handles.

Can I install these stripes myself?

Yes. The kit ships with transfer tape and installs wet or dry. Clean the panel thoroughly, position the stripe, squeegee from the center outward, and remove the carrier film. A wet install gives you extra time to reposition before the adhesive sets.

Will the stripes damage my paint when I remove them?

When removed correctly, no. Warm the vinyl with a heat gun or hair dryer and peel it slowly at a low angle. The stripe should come off in one piece. Wash and wax the area afterward, and avoid installing over fresh paint that has not fully cured.

Is this an official brand product?

Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.