Patriotic Semi Truck Decals | Eagle & USA Flag Decal Set

Description

A swooping eagle and American flag decal set printed on durable cast vinyl, sized for semi truck doors, sleeper panels and trailers. Made for drivers who want a bold patriotic look on the road.

Eagle & Flag American Flag Decal Set for Big Rigs

This two-piece patriotic set pairs a swooping eagle graphic with a matching USA flag design, cut from cast vinyl and ready to apply to your truck. Choose a width from 12 inches up to 48 inches so the pair fits your door, sleeper panel or trailer side without trimming guesswork. The graphics are printed in-house with fade-resistant inks on matte, gloss or clear vinyl, so you can match the look you want, from a clean low-sheen finish to a high-shine statement. Whether you run regional routes or cross-country hauls, this set gives your rig a proud, all-American identity that stands out at every truck stop and weigh station.

Sizing Your Decals for Truck Doors and Trailers

Measure the flat area where you plan to apply each piece before ordering. A 12-inch set works well on toolboxes, fuel tank covers and smaller door panels, while 24-inch and 30-inch widths suit standard cab doors. For sleeper panels, trailer sides and drop-deck trailers, the 36-inch and 48-inch options fill the space with fewer seams and more visual impact. Each decal is cut with a small border of clear space around the artwork, so account for that when planning placement near door handles, rivet lines or high-visibility striping. If you are layering the eagle over the flag, apply the flag first and let it set before positioning the eagle.

Cast Vinyl Built for Highway Miles

We print every set on cast vinyl, a thin, conformable material that follows the slight curves and panel contours of a cab or trailer without lifting at the edges. The matte option cuts glare in sunlight and pairs naturally with painted aluminum and fiberglass panels. Gloss adds depth and shine for drivers who want the artwork to pop. Clear vinyl lets the underlying surface show through open areas of the design for a painted-on look. All three finishes apply with a pressure-sensitive adhesive and a release liner, using the same wet-or-dry method you already know from striping and lettering work.

Applying Your Patriotic Decal Set

Start with a clean, dry surface, free of wax, diesel film and road grime, ideally above 50 degrees Fahrenheit. Position each decal with masking tape hinges, peel the liner back gradually, and squeegee from the center outward to push out air. On larger widths, a helper makes alignment easier, especially on trailer sides where you are working at height. Cast vinyl conforms around gentle curves when warmed slightly with a heat gun or hair dryer, and it can be repositioned during application before full pressure is applied. Once set, wash normally, avoiding high-pressure spray directly at the edges.

Pairing Your Decal Set with Other Truck Graphics

This eagle and flag decal set works well alongside other graphics you may already run on your cab or trailer. The bold red, white, and blue palette pairs naturally with simple lettering, DOT numbers, or striping, so you can build a cohesive look without clashing colors. If you plan to combine the decals with additional graphics, leave a few inches of breathing room around each piece so the eagle and flag remain easy to read at highway speeds. Consider placement on flat, smooth panels first, since curves and rivets can complicate layering multiple graphics. Whether you run a single truck or manage a small fleet, this set gives you a consistent patriotic theme you can repeat across every vehicle in the lineup.

Caring for Your Decals Through the Seasons

A little routine care keeps this decal set looking sharp season after season. Wash by hand with mild soap and water, using a soft cloth or sponge rather than abrasive brushes found at automated washes, which can scuff the surface over time. Avoid high-pressure sprayers aimed directly at the decal edges, since forced water can lift corners and weaken adhesion. In winter, gently clear snow and ice rather than scraping across the graphics. Skip harsh solvents, fuel drips, and citrus-based cleaners, as these can dull the finish. When you park for long stretches, shade helps slow fading from direct sun. With regular washing and sensible care, the colors stay crisp and the edges stay sealed for many miles down the road.

What you get

• Two-piece set: swooping eagle graphic plus matching USA flag design
• Available in 12-inch to 48-inch widths to fit doors, sleepers and trailers
• Printed on cast vinyl that conforms to curved truck panels
• Choice of matte, gloss or clear finish
• Pressure-sensitive adhesive with release liner for straightforward application
• Fade-resistant inks suited to long highway exposure
• Made to order in our US shop

Specifications

Frequently asked questions

Can I put these decals on my trailer instead of my cab doors?

Yes. The set works on any clean, smooth surface including trailer sides, sleeper panels and toolboxes. For large trailer areas, the 36-inch or 48-inch width fills the space better than smaller sizes.

Which finish should I choose?

Matte reduces glare and blends with painted panels, gloss adds shine and depth, and clear lets your surface show through open areas of the design for a painted-on look. All three use the same cast vinyl base.

Will these hold up to pressure washing?

Once fully applied, the decals tolerate normal washing. Avoid aiming a high-pressure nozzle directly at the edges, and keep the wand a reasonable distance from the graphics, as you would with any vinyl lettering.