Aries Tribal Stripe Car & Truck Vinyl Graphics Set

Description

A set of tribal stripe decals with a ram-horn Aries design, cut from cast vinyl for cars, trucks and SUVs. Choose a width from 12 to 48 inches to fit your build.

Aries Tribal Stripes That Read Bold at Any Width

This graphic set pairs sweeping tribal stripe lines with a stylized ram-horn Aries motif, giving your hood, doors or tailgate a layered, hand-drawn look. Each stripe tapers and hooks the way tribal art should, so the design flows with body panels instead of fighting them. Because the set is cut to your chosen width, the same artwork can sit subtle along a rocker panel or stretch across a full truck hood. The matte option reads like painted-on graphics, while gloss adds punch under sunlight. If you want a clean way to signal your zodiac sign without a bumper sticker, this set does it with a design that looks intentional from ten feet away or at highway speed.

Cast Vinyl Built for Daily Drivers and Work Trucks

We cut these tribal decals from cast vinyl, the conformable choice for vehicle graphics. Cast film stretches and curves around body lines, door seams and gentle fender contours without lifting at the edges, which matters on trucks that see weather year-round. The vinyl is printed and contour-cut in our shop, then premasked so the whole stripe set goes down as one piece per side. Apply it to clean, wax-free paint, glass or smooth metal. Whether your truck is a weekend show build or a daily hauler that lives outside, the material is chosen to hold up to washing, road spray and sun without cracking along the cut lines.

Choosing Your Stripe Width and Placement

The set is offered in widths from 12 inches up to 48 inches, measured at the widest point of the stripe layout. Smaller widths suit mirror caps, rear windows, toolboxes or the lower door of a compact car. Mid sizes work along rocker panels, fender flares or a single door. The largest widths are made for full hoods, tailgates or running the length of a pickup bed. Before ordering, measure the flat area you plan to cover and compare it to the listed width, leaving a little clearance at panel edges. The stripe proportions scale with the width, so the design stays balanced whether you go small or go wide.

Applying Your Tribal Decals Without Bubbles

Start with a warm, clean surface: wash the area, remove wax with isopropyl alcohol, and let the panel dry fully. Position the premasked decal with small pieces of tape, then peel the backing away and press from the center outward with a squeegee or credit card. Working in the shade or a garage keeps the vinyl from grabbing too aggressively. Once the decal is down, go over it again with firm, overlapping strokes, then pull the application tape back on itself at a low angle. Small air pockets can be worked to the edge or pierced with a pin and flattened. Wait a day before washing so the adhesive sets.

What you get

• Aries ram-horn tribal stripe design sold as a complete set
• Available in 12-inch to 48-inch widths to fit cars, trucks and SUVs
• Cut from conformable cast vinyl that follows body lines and curves
• Choose matte for a painted look, gloss for shine, or clear for a subtle tone-on-tone effect
• Premasked and ready to apply with a squeegee, no special tools needed
• Contour-cut in our US shop to order
• Works on paint, glass and smooth metal surfaces

Specifications

Frequently asked questions

Do I get both sides of the truck graphic?

Yes. The set includes mirrored left and right stripe decals so the design matches on both sides of your vehicle. Each piece ships premasked for a one-piece installation.

What width should I order for my hood or doors?

Measure the flat area you want to cover and pick the closest width that fits with an inch or two of clearance at the panel edges. Rocker panels and doors usually take small to mid widths, while full hoods and tailgates call for the larger sizes.

Can these tribal decals be removed later?

Yes. Warm the decal with a hair dryer or heat gun on low and peel it away slowly at a shallow angle. Any remaining adhesive can be cleaned off with isopropyl alcohol. Removal is easiest when the vinyl is warm.