Matte Racing Stripes Pair for Toyota Hood | Vinyl Decal Set

Description

A pair of matte black racing stripes cut from Cast Vinyl, made for drivers who want a clean motorsport look on their hood. Sold in four decal sizes so you can match the stripe width to your build.

Matte Toyota Racing Stripes That Read as Paint, Not Sticker

The flat finish on this stripe pair is the whole point. Matte vinyl absorbs light instead of bouncing it back, so once the stripes are down and squeegeed flat, they blend into a factory-style paint job rather than sitting on top of it. Each set is cut as a matched left and right stripe, so the spacing and taper stay consistent across the hood without you having to measure and trim two separate pieces. The matte surface also hides minor scuffs and water spots far better than a gloss finish, which matters if the vehicle lives outside. Apply them over a clean, wax-free hood and the edges lay tight with no silvering or lift at the taper.

Choosing Your Stripe Width

This pair is offered in four decal sizes: 4, 8, 12 or 18 inches, measured across each stripe. A 4-inch stripe is a subtle accent that works well on smaller hoods or as a first decal if you want to test the look before committing to something wider. The 8-inch pair is the classic muscle-car proportion most buyers picture when they think of racing stripes. The 12 and 18-inch options make a bolder statement and suit wider hoods where thin stripes can get lost in the body lines. If you are pairing these with other Toyota racing stripes or layering them near existing decals, measure the open hood space first and pick the size that leaves even margins on both sides.

Cast Vinyl Built for Outdoor Use

We cut these stripes from Cast Vinyl, the conformable grade that curves around body lines and hood contours without wrinkling or lifting at the edges. Cast film is thinner and more flexible than calendered vinyl, which is why it holds down through car washes, rain, sun and daily driving. The matte finish is laminated into the film itself, not printed on top, so it will not rub off or turn shiny where your hands or a wash mitt touch it most. Application is a standard wet or dry install with transfer tape: position the pair, squeegee from the center outward, pull the tape slowly at a low angle, then let the adhesive set before the first wash.

Installing Your Stripe Pair

Start with a cool hood out of direct sunlight and wash it thoroughly, then remove any wax with isopropyl alcohol so the adhesive bites properly. Dry-fit both stripes and mark the centerline of the hood with low-tack tape, since a centered pair is what sells the racing look. Peel the backing, mist the hood if you prefer a slide-adjustable install, and set the first stripe against your centerline mark. Squeegee from the middle outward to push out air and moisture, then repeat mirrored on the second stripe. Pull the transfer tape back on itself, slow and flat. Keep the hood dry for the first day, and avoid pressure washing directly at the stripe edges for the first week.

What you get

• Matched left and right stripe pair for a centered racing layout
• Matte black Cast Vinyl with a non-High-Visibility, paint-like finish
• Four decal sizes: 4, 8, 12 or 18 inches per stripe
• Conformable film wraps hood contours without wrinkling
• Matte finish is part of the vinyl, not a printed surface layer
• Wet or dry application with included transfer tape
• Clean, residue-free removal when you want a change

Specifications

Frequently asked questions

Will these stripes fit my specific hood?

The stripes are sold by decal size rather than by vehicle model, so fitment comes down to your measurements. Measure the flat area of your hood and choose the 4, 8, 12 or 18-inch stripe width that leaves even margins on both sides. The Cast Vinyl can be trimmed during install if you need to shorten the length.

Can I apply these over a hood with existing decals or paint protection?

These stripes adhere best to clean, wax-free factory paint. Applying over textured films, ceramic coatings or existing decals can weaken the bond and cause lifting at the edges. If your hood has a coating, test adhesion in a small area first.

How do I remove the stripes later?

Warm the vinyl gently with a hair dryer on a low setting and peel the stripe back on itself at a flat angle. Cast Vinyl typically releases in one piece from factory paint. Clean any remaining adhesive with isopropyl alcohol.

Is this an official brand product?

Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.