Blade Sword Semi Truck Decals | Custom Car Decals

Description

Blade-style sword vinyl graphics cut to your chosen width, made for semi trucks and other large vehicles. A bold custom car decals option for drivers who want their rig to stand out.

A Sword Graphic Built for Semi Truck Doors and Sleeper Panels

This blade-inspired sword decal set brings a sharp, aggressive look to your semi truck. The sweeping design works well on sleeper cab panels, trailer sides, or toolboxes, giving your rig a distinctive profile at rest stops and loading docks alike. Each piece is cut from cast vinyl, so it follows the gentle curves and panel lines of a cab without fighting the surface. Whether you run a single truck or manage a small fleet, this graphic gives your equipment a consistent, recognizable identity. Choose a width from 12 to 48 inches to match the space you are working with, from a subtle accent near the door handle to a full statement across the trailer side.

Choose Your Size and Finish

Every set is offered in widths from 12 inches up to 48 inches, so you can scale the design to fit your truck rather than forcing a one-size graphic into an awkward spot. Measure the flat area you plan to apply it to, then pick the width that leaves comfortable clearance around door handles, hinges, and reflectors. You can also select the finish that suits your style: matte for a low-key, painted-on look, gloss for a bright, polished appearance, clear for an understated overlay effect, or static cling if you want a removable option that peels off cleanly when the lease ends or the season changes. Static cling is a good fit for drivers who swap graphics often.

How to Apply Your Custom Car Decals

Application is a straightforward afternoon job with basic tools. Clean the surface with isopropyl alcohol and let it dry completely, then position the decal with masking tape as a hinge before peeling the backing. Work the vinyl down with a squeegee or credit card from the center outward to push air toward the edges. On larger sizes, a helper makes alignment easier, especially on trailer panels where you want both sides to sit at matching heights. Avoid applying in cold weather or direct sunlight; a mild, shaded day gives the best results. Once applied, go over the edges again to seal them down, and keep washing gentle for the first day or two.

Care and Removal

After application, routine care keeps the graphic looking sharp. Hand washing or a standard truck wash is fine; avoid high-pressure spray aimed directly at the edges, and skip abrasive brushes over the decal itself. For removal, warm the vinyl with a heat gun or hair dryer on a low setting and peel it back slowly at a shallow angle, working section by section. Any remaining adhesive can be cleaned off with an adhesive remover and a soft cloth. If you chose static cling, removal is even simpler: peel it off and save it on its original liner for reuse later. Store rolled graphics flat or loosely rolled in a cool spot away from direct sun.

What you get

• Blade sword graphic set cut from cast vinyl for flexibility on curved panels
• Available in 12, 18, 24, 36, and 48 inch widths
• Choose matte, gloss, clear, or static cling finish
• Sold as a matched set sized to your selected width
• Suitable for semi truck doors, sleeper panels, trailers, and toolboxes
• Removable with heat; static cling version peels off cleanly without adhesive
• Cut to order in the USA

Specifications

Frequently asked questions

How do I pick the right width for my truck?

Measure the flat area where you plan to place the graphic, then choose a width that leaves an inch or two of clearance on each side. A 12 to 24 inch width works well on cab doors, while 36 and 48 inch sizes suit sleeper panels and trailer sides.

Will these decals damage my paint when removed?

When removed correctly with gentle heat and slow peeling, the vinyl lifts away without harming factory paint. Avoid pulling aggressively in cold weather, and clean any leftover adhesive with an approved adhesive remover.

Can I get the sword graphic in a different finish than shown?

Yes. Every set is available in matte, gloss, clear, and static cling. Static cling is the best choice if you want a removable, reusable option with no adhesive at all.