Ranger Name Plate Window Decal in Gloss | Ford Bronco Decal

Description

A gloss-finish name plate decal for truck owners who want a clean, lettered look on their rear window or tailgate. Cut from Cast Vinyl in your choice of four practical sizes.

A Gloss Name Plate That Completes Your Ranger Build

This name plate decal is cut from Cast Vinyl with a smooth gloss finish that reads like painted lettering once applied. It suits the rear window, but it also works on a tool box, cooler, windshield corner, or any smooth surface around your rig. If you are building out a full look, pair it with pieces from our Ford Bronco decal kit collection, where matching graphics and lettering live together. The gloss surface wipes clean with mild soap and water, and the decal applies with a standard wet or dry method using transfer tape. Choose the size that matches your space and keep the layout simple and sharp.

Choosing Between 4, 8, 12 and 18 Inch Sizes

Size is the biggest decision with a name plate decal, so here is a simple way to think about it. The 4 inch cut works well for a corner placement, a mirror housing, or a small accent on a cooler lid. The 8 inch size fits most rear window corners and tool box lids without crowding the space. At 12 inches, the lettering starts to read clearly from a few car lengths away, which makes it a popular pick for tailgates and rear glass. The 18 inch option is the statement size, best for a wide window or a full-width placement where you want the name to carry. Measure your spot before ordering and leave a little breathing room on each side.

How to Apply Your Window Decal Without Bubbles

Start with a clean, dry surface free of wax, dust, and streaks. Position the decal with a strip of masking tape along one edge as a hinge, then peel the backing away a little at a time while smoothing the lettering down with a squeegee or a credit card wrapped in a soft cloth. Work from the center outward so air pushes to the edges instead of trapping under the vinyl. If you prefer the wet method, lightly mist the surface with soapy water, float the decal into place, squeegee out the liquid, and let it set before removing the transfer tape. Pull the tape back slowly at a low angle, parallel to the surface, and the letters stay put.

Care, Removal, and Ordering Details

To keep the gloss finish looking sharp, wash around the decal gently and avoid high-pressure spray nozzles aimed directly at the lettering. When it is time for a change, warm the decal with a hair dryer on a low setting and peel it away slowly; any leftover adhesive usually comes off with a mild adhesive remover and a soft cloth. Each order is printed and cut to order in our, so your decal arrives fresh and ready to apply with transfer tape already in place. Pick your size at checkout, and if you are outfitting a whole vehicle, browse the matching graphics in the same collection so the finishes and lettering styles stay consistent across the build.

What you get

• Cast Vinyl construction cut to a crisp name plate design
• Gloss finish that reads like painted lettering
• Available in 4, 8, 12, or 18 inch decal sizes
• Applies to rear windows, tool boxes, coolers, and smooth surfaces
• Transfer tape included for easier placement
• Printed and cut to order in our US
• Removable with gentle heat when you want a change

Specifications

Frequently asked questions

Will this decal work on a rear window with defroster lines?

Yes. The vinyl applies over defroster grid lines without issue. Press firmly so the lettering bonds evenly across the lines, and use the dry application method for the cleanest result on textured glass areas.

Which size should I choose for a rear window?

Many customers pick the 8 or 12 inch size for rear glass, since the lettering stays readable without covering the whole window. The 4 inch works for corner accents, and the 18 inch suits wide placements. Measure your space first and compare it to the listed decal size.

Can I remove the decal later without damaging the glass?

Yes. Warm the decal gently with a hair dryer on a low setting and peel it back slowly at a shallow angle. Any remaining adhesive can be cleaned off with a mild adhesive remover and a soft cloth.

Is this an official brand product?

Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.