Ford Bronco Decal Kit - Side Stripe Vinyl Decals

Description

A side stripe decal kit cut from outdoor-rated vinyl, made for drivers who want a clean two-tone look along the body line. Choose matte, gloss, static cling or clear finishes in four decal sizes.

A Ford Bronco Decal Kit Built for the Body Line

This side stripe kit is designed to follow the lower body line of a boxy, trail-ready SUV, giving the doors and rear quarter a layered racing-inspired look without paint. Each stripe is cut individually from cast or calendered vinyl so you can space the pieces to match your trim and fender layout. The kit ships as a matched left and right set, so both sides of the vehicle mirror each other. Because the stripes are separate decals rather than one large wrap panel, you can install them one at a time, repositioning each piece with a slip solution before it sets. It is a straightforward project for a first-time installer with patience and a squeegee.

Four Finishes and Four Decal Sizes

Every kit is printed in your choice of matte, gloss, static cling or clear vinyl. Matte gives a low-sheen, painted-on look that hides fingerprints and wax swirls. Gloss reads like fresh clear coat and pops against flat factory paint. Static cling pieces apply without adhesive, so they are a good pick for lease vehicles or anyone who wants a temporary look before committing. Clear vinyl works as a subtle protective layer or an underlayer for a layered build. Sizes run 4, 8, 12 or 18 inches, measured by stripe height. Smaller sizes suit door accents and rear quarters, while the larger sizes stretch the full side profile for a bolder statement.

Installation Tips for Clean Stripe Alignment

Start with a washed and decontaminated surface, free of wax and polish, and work in shade so the surface is cool to the touch. Lay out the full set against the body line with masking tape before peeling any backing, and step back to check the spacing from both front and rear. Use a light slip solution on the surface for the larger stripes so you can slide each decal into position, then squeegee from the center outward to push liquid out. Skip the edges until last to avoid lifting the vinyl. Wait a full day before washing, and avoid pressure washing directly at the stripe edges during routine cleaning.

Care, Removal and Reordering

For daily care, hand wash with mild car soap and a soft mitt, working along the stripe direction rather than across it. Avoid automated brush washes, since brushes can catch an edge. When you are ready to remove the stripes, warm them gently with a hair dryer on low and peel slowly at a shallow angle; adhesive residue comes off with a citrus-based cleaner and a microfiber towel. Static cling pieces simply peel off with no residue at all. If you want to refresh one side after trail damage or reorder a different size later, replacement pieces are available, so you do not need to buy a full second kit.

What you get

• Matched left and right side stripe set for a symmetrical finish
• Available in matte, gloss, static cling and clear vinyl
• Four decal sizes: 4, 8, 12 or 18 inches
• Cut from cast or calendered vinyl for outdoor use
• Individually cut stripes allow custom spacing along the body line
• Static cling option applies with no adhesive for lease-friendly use
• Replacement pieces available without buying a whole new kit

Specifications

Frequently asked questions

How do I choose the right decal size?

Measure the height of the area you want the stripes to cover, from the body line down. A 4 or 8 inch set works for door accents, while 12 or 18 inch sizes suit a full side stripe look. When in doubt, tape a paper template to the vehicle first.

Will the stripes damage my paint?

Applied to factory paint in good condition and removed warm, the adhesive-backed vinyl should not damage the finish. Avoid installing on fresh or repainted panels that have not fully cured. The static cling option uses no adhesive at all.

Can I install this myself?

Yes. The kit is cut into individual stripes so you can position one piece at a time. A squeegee, masking tape, and a slip solution of water with a drop of dish soap are all you need for the larger sizes.

Is this an official brand product?

Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.