By vehicle
By style
By position
Guides
Marine & water
Powersports
Storefront & office
Labels & packaging
Bulk & wholesale
Send your own artwork
Upload your logo or sketch on any product page: we cut it in the width you choose.
Shop
Kids & anime
Sports & fan
Custom stickers
Start here
Your design, our vinyl
Send a sketch or logo, optional upload box sits under the size selector on every product.
Finishes we print
Sizes we cut
12"18"24"36"48"
A two-piece hood decal set cut from Cast Vinyl, sized for truck owners who want racing stripes without a full wrap. Choose 4, 8, 12 or 18 inch stripe widths at checkout.
JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.
This decal set was drawn with the Ram 2500 hood in mind, so the stripe pair follows a clean center-line layout that works on flat and slightly contoured hoods. Each set includes a left and right stripe, cut from Cast Vinyl that conforms to curves without lifting at the edges. You pick the width: 4 inch stripes for a subtle accent, 8 or 12 inch for a classic muscle-truck look, or 18 inch when you want the stripes to dominate the hood. The set ships ready to apply with a peel-and-stick backing, and it can be layered over factory paint or an existing flat finish. If you have been searching for dodge racing stripes that fit a heavy-duty truck rather than a sports car, this is that set.
Every set is printed in-house, and you choose the finish before adding it to your cart. Matte gives a low-key, almost painted-on look that hides glare. Gloss reads like fresh clear coat and matches most factory paint. Clear stripes work over any color if you want a ghost effect, and static cling lets you test the placement with zero commitment since it peels off clean with no adhesive. All four finishes use the same cut pattern, so the layout stays identical no matter which one you pick. If you change your mind later, the vinyl removes with heat from a hair dryer or heat gun, and any residue comes off with standard adhesive remover.
Start with a clean, dry hood; wash off wax and road film first, because any residue under the stripe will show. Lay each stripe in position with light masking tape to check alignment against the hood crease before you commit. Peel the backing, mist the surface if you prefer a slip application, and squeegee from the center outward to push out air. Cast Vinyl has enough give to stretch around gentle curves, so work slowly on the front edge where the hood rolls. Keep the truck parked out of direct sun for the first day while the adhesive sets. Full placement tips are included in the package, and the process is the same for all four size options.
Stripe widths are 4, 8, 12 or 18 inches, measured at the widest point of each decal, and the pair is mirrored so both sides match. Priced in the same range you will see across custom truck graphics, typically between $24.99 and $44.99 depending on size and finish. To keep the stripes looking sharp, wash by hand or with a soft brush at a touchless wash, and avoid high-pressure spray directly at the stripe edges. Matte finishes should stay away from wax, since it can create shiny patches. If you want to add rocker panel or tailgate accents later, this set pairs with the rest of our Ram 2500 collection.
The set is cut in a mirrored pair sized for Ram 2500 hoods, but hoods vary by year and trim. The 4 to 18 inch widths give you room to position the stripes where they fit best, and Cast Vinyl stretches slightly over gentle curves.
Gloss matches most factory paint, matte gives a muted look, clear works as a ghost stripe over any color, and static cling is best if you want to test placement or remove the stripes often since it uses no adhesive.
Warm the vinyl with a hair dryer or heat gun and peel it away slowly. Any leftover adhesive can be cleaned with a standard adhesive remover safe for automotive paint.
Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.
4 inch, 8 inch, 12 inch, 18 inch
Your shopping cart is empty
Notifications