Racing Stripe Vinyl Decal for Cars - Honda Graphics Kit Stripe

Description

A pair of matte, gloss or clear vinyl racing stripe decals cut to your choice of 4, 8, 12 or 18 inch lengths. Made for drivers who want a motorsport look on their daily sedan without permanent paint work.

A Classic Racing Stripe, Cut to Your Preferred Length

This twin-stripe decal set brings a track-inspired accent to any smooth exterior surface. Each stripe is precision cut from Cast Vinyl and available in 4, 8, 12 or 18 inch lengths, so you can scale the look to fit a hood, trunk lid, fender or rear bumper. The 12 inch size is a popular middle ground for accent placement, while the longer cut suits full panel runs. Choose a matte finish for a subtle, low-key motorsport feel, a gloss finish for a bold painted-on look, or a clear finish if you want the stripe shape without added color. Every set ships ready to apply with transfer tape already in place.

Why Drivers Add This Stripe to a Honda Graphics Kit

A racing stripe is one of the simplest building blocks in any honda graphics kit, and it pairs well with other decals you may already run, from door numbers to fender flags. Because the stripe set is sold by length rather than as a fixed body kit, you control where and how it lands on the car. Apply the pair centered on the hood or trunk, split them across both front fenders, or run them along the lower doors for a rally-inspired layout. The clean parallel lines work on any paint color, and the vinyl conforms to gentle panel curves without lifting at the edges when installed on a clean, warm surface.

Finish Options and How Each One Reads on Paint

Matte vinyl gives the stripe a flat, understated appearance that reads as a factory-style accent, especially on darker paint. Gloss vinyl catches light the same way clearcoat does, so the stripe blends into a glossy finish and looks painted rather than stuck on. Clear vinyl is nearly invisible on the surface and works well as a protective or layered accent over existing paint lines. All three finishes are cut from the same Cast Vinyl base, which is thinner and more flexible than calendered vinyl, so it follows body lines and curves with less risk of visible edges. Pick the finish that matches the sheen of your paint for the most integrated result.

Applying Your Stripe Decals Step by Step

Start by washing the area with dish soap and water, then wiping it down with isopropyl alcohol to remove wax and residue. Park out of direct sunlight and let the panel reach room temperature before you begin. Position the first stripe with small strips of masking tape, measure the gap to the second stripe, then hinge the decal with tape along one edge. Peel the backing away, squeegee from the center outward, and remove the transfer tape slowly at a low angle. Repeat for the second stripe, then check alignment from a few feet back. Avoid washing the car for the first few days while the adhesive fully bonds to the paint.

What you get

• Available in 4, 8, 12 and 18 inch decal lengths
• Sold as a matching pair of parallel racing stripes
• Cut from Cast Vinyl for flexibility on curved panels
• Choose matte, gloss or clear finish
• Ships pre-masked with transfer tape for easy alignment
• Works on hoods, trunks, fenders, doors and bumpers
• Removable with heat without leaving residue on most surfaces

Specifications

Frequently asked questions

Which stripe length should I choose for my car?

The 12 inch length works well as a centered accent on a hood or trunk. Choose 4 or 8 inches for smaller areas like fenders or mirror caps, and 18 inches if you want the stripes to run across a longer panel. Measure your intended area before ordering to confirm the fit.

Will the stripes damage my paint when I remove them?

On original, well-adhered paint, warming the vinyl with a hair dryer or heat gun on low and peeling slowly typically removes it without residue. Any remaining adhesive can be cleaned with isopropyl alcohol. Avoid applying over fresh or repainted panels that have not fully cured.

Can I layer other decals over or next to these stripes?

Yes. The stripes work as a base element alongside other decals in a graphics kit. For the cleanest look, apply the stripes first, let the adhesive set, then position additional decals around them using the same surface prep steps.

Is this an official brand product?

Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.