Matte Black Hood Decal Pair - Ford Bronco Decal Kit Style

Description

A pair of matte black Cast Vinyl hood decals cut to a clean, low-profile stripe look. Made for owners of American muscle cars and pony cars who want a subtle blackout accent on the front end.

A Matte Black Hood Decal Pair Built for Clean Stripe Looks

This two-piece decal set is cut from matte black Cast Vinyl and designed to lay along the hood of your muscle car for a blackout stripe effect. The matte finish absorbs light instead of reflecting it, so the decals read as painted-on graphics rather than stickers. Each decal in the pair is cut to the same shape so the left and right sides mirror each other across the hood line. Choose the size that matches your hood proportions: 4, 8, 12 or 18 inches. The smaller sizes suit a subtle accent near the scoop or vents, while the larger cuts make a bolder statement across the full hood width. Application takes only a few minutes with a squeegee and soapy water.

How This Pair Fits Into Your Ford Bronco Decal Kit Build

If you are building out a coordinated vinyl theme across your vehicle, this hood pair works alongside other decals in our truck and muscle car collections. Many buyers pair a hood set like this with side stripes, window graphics or a rear accent to tie the whole look together. Because every piece we print uses the same matte black Cast Vinyl, the shade and sheen stay consistent from panel to panel. That consistency matters when you are mixing pieces from a larger decal kit, since mismatched blacks from different sources can look patchy in sunlight. Order this pair on its own or stack it with other matte black pieces for a uniform, factory-style blackout treatment across the front end.

Matte Black Cast Vinyl That Reads as Paint, Not Plastic

We print and cut this pair on matte black Cast Vinyl, a thin, conformable film that follows gentle body curves without lifting at the edges. The matte surface scatters light, hiding minor imperfections and fingerprints far better than a gloss film would. Cast Vinyl also resists shrinking and edge curl better than thicker calendered films, which helps the decals hold their cut shape over time. The adhesive is pressure-sensitive and repositionable during wet application, so you can nudge each piece into alignment before squeegeeing out the water. Once set, the film stays put through washes and weather. Removal is straightforward with heat, and the adhesive is engineered to come off cleanly without leaving residue behind.

Sizing, Application and Care for Your Hood Decal Pair

Each pair is available in four cut sizes: 4, 8, 12 or 18 inches, measured along the longest edge of each decal. Before ordering, measure the hood area you want to cover and pick the size that leaves even margins on both sides. For application, clean the paint with isopropyl alcohol, mist the area with soapy water, position each decal, then squeegee from the center outward to push out water and air. Skip the squeegee pass on the transfer tape until the decal is fully seated. Wait 24 to 48 hours before washing. For ongoing care, hand wash with mild soap and avoid high-pressure spray directly on the edges. Avoid waxing over the decals, as wax can build up along the cut line.

What you get

• Two-piece mirrored set for left and right hood placement
• Matte black Cast Vinyl with a paint-like, low-sheen finish
• Available in 4, 8, 12 or 18 inch cut sizes
• Wet-install application with repositionable adhesive
• Precision machine-cut edges for clean stripe lines
• Printed and shipped by our US-based
• Removable with heat without leaving residue

Specifications

Frequently asked questions

How do I choose between the 4, 8, 12 and 18 inch sizes?

Measure the hood area you want the pair to cover, then pick the cut size that fits within it with even spacing on both sides. The 4 and 8 inch sizes work as accents near vents or scoops, while 12 and 18 inch cuts suit wider stripe placements.

Will the matte finish match other matte black decals I already have?

We print all our matte black pieces on the same Cast Vinyl, so pieces ordered together will match in shade and sheen. Decals from other sources may not match exactly, since matte blacks vary between manufacturers.

Can I remove these hood decals later?

Yes. Warm the decal with a hair dryer or heat gun on a low setting and peel slowly at a shallow angle. The adhesive is designed to release cleanly without leaving residue on properly maintained paint.

Is this an official brand product?

Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.