By vehicle
By style
By position
Guides
Marine & water
Powersports
Storefront & office
Labels & packaging
Bulk & wholesale
Send your own artwork
Upload your logo or sketch on any product page: we cut it in the width you choose.
Shop
Kids & anime
Sports & fan
Custom stickers
Start here
Your design, our vinyl
Send a sketch or logo, optional upload box sits under the size selector on every product.
Finishes we print
Sizes we cut
12"18"24"36"48"
A gloss Vinyl Decal kit for dirt bike riders who want a fresh, custom look on their plastics. Cut in your choice of 4, 8, 12 or 18 inch decal sizes and printed in our.
JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.
This honda graphics kit is printed on gloss Cast Vinyl with a smooth, high-shine surface that stands out against shrouds, fenders and number plates. Each kit is cut to a bold race-inspired layout with panels, accents and trim pieces you can arrange your own way, so your bike looks put together whether it is parked in the garage or lined up at the gate. The gloss finish resists scuffs from routine washing and trail debris, and the print holds its color under regular riding conditions. Choose the decal size that matches your build, from a subtle 4 inch accent set up to full 18 inch coverage pieces, and give your machine a clean, finished look without paying for a full wrap.
Every kit is sold by decal size, which is the tallest measurement of the largest piece in the set. A 4 inch kit works well for number plates, fork guards and small accent areas. The 8 inch size suits side panels and rear fenders on smaller frames. A 12 inch kit covers shrouds and radiator wings on most full-size bikes. The 18 inch option gives you the largest panels for big shrouds and full side coverage. Because the pieces are individual decals rather than one printed sheet, you can trim around vents, bolt holes and edges with a hobby knife for a tidy fit, and you can skip any piece you do not need.
Start with clean, dry plastics. Wash off mud and chain lube, then wipe the application areas with isopropyl alcohol and let them fully dry. Peel each decal from its backing, position it before pressing it down, and work from the center outward with a squeegee or soft cloth to push air toward the edges. On cool days, warm the decal slightly with a hair dryer so it conforms to curves and corners. Avoid riding or washing the bike for about 24 hours so the adhesive sets. If you need to reposition a piece right after placing it, peel it back slowly and lay it down again before pressing it firm.
We print every kit in our US on Cast Vinyl with a gloss laminate, so the color and shine come from materials we stand behind, not a third-party catalog. Each order is packed with application tape on the larger panels, a small squeegee, and illustrated instructions so you can install the set with basic hand tools. If a piece arrives damaged or you are not sure which decal size fits your plastics, message us before installing and we will help you sort it out. We keep our pricing well below the typical dealer graphics counter, with the same attention to detail you would expect from a that rides too.
This is a universal decal kit, not model-specific. Because the pieces are individual decals sold by size, you trim them to fit your plastics. Measure the height of the area you want to cover and pick the closest decal size: 4, 8, 12 or 18 inches.
The decal size is the tallest measurement of the largest piece in the set. Use 4 inch for number plates and accents, 8 inch for side panels, 12 inch for shrouds on most full-size bikes, and 18 inch for large shroud and side coverage.
Yes. We print this layout in matte, gloss, clear and static cling. If you want a different finish than the one listed, contact us before ordering and we can set it up for you.
Not affiliated with or endorsed by the manufacturer. It is an independent aftermarket Vinyl Decal.
4 inch, 8 inch, 12 inch, 18 inch
Your shopping cart is empty
Notifications
