Skull Wing Helmet Sticker Vinyl Decal for Riders

Description

A skull and wing Vinyl Decal cut from durable Cast Vinyl, made for riders who want bold helmet stickers that hold up on the road. Available in 4, 8, 12 or 18 inch sizes.

A Skull Wing Design Built for Motorcycle Helmets

This skull wing decal brings a classic rider attitude to any motorcycle helmet. The detailed artwork pairs a stylized skull with spread wings, creating a design that reads clearly from a distance and looks sharp up close. Each decal is die-cut to follow the shape of the artwork, so there is no clear or white background box sitting on your lid. Whether you ride a cruiser, a sport bike or a touring rig, this Graphic adds personality without covering your entire helmet. Choose the size that fits your shell best: a 4 or 8 inch decal works well on the sides, while 12 and 18 inch options suit full-face helmets, fairings, tanks or flat surfaces on your gear. It is a straightforward way to make your mark.

Cast Vinyl Made to Handle the Ride

We print this helmet sticker on Cast Vinyl, a thin and flexible material that conforms to the gentle curves of a helmet shell without lifting at the edges. The inks are laid down in a matte or gloss finish, so you can pick the look that matches your gear: matte blends into a flat-painted helmet, while gloss adds a clean shine. The decal is contour-cut with a premask application layer, which keeps the thin wing details aligned while you position it. Once applied, the material resists everyday exposure to sun, rain and road grime. Wipe it down with a soft cloth when you clean your helmet and the Graphic stays looking like it did on day one.

Applying Your Helmet Stickers in Minutes

Application takes only a few minutes with the dry method. Start with a clean helmet surface: wash off dust and wax, then let it dry completely. Peel the paper backing, position the decal using the premask layer, and press from the center outward to lock it down. Work any air bubbles toward the edges with your fingers or a squeegee. Slowly peel the premask away at a low angle and the decal stays behind. For curved areas near vents or edges, go slow and let the vinyl stretch into place. If you are placing it on a freshly painted or waxed helmet, wait until the surface is fully cured. One person, one decal, one clean afternoon and your helmet is done.

Sizing, Finish and Set Details

This skull wing Graphic is sold in four decal sizes: 4, 8, 12 and 18 inches, measured at the longest point of the design. That range covers everything from a small accent on the back of a half helmet to a large statement piece on a full-face shell or fuel tank. Each order includes one die-cut decal with premask applied, ready to position and press on. Pick matte for a low-key, printed look or gloss for a bolder finish; both are printed on the same Cast Vinyl base. Because the decal is cut to shape, it layers cleanly over solid paint colors without hiding more surface than the artwork itself needs. Order the size that matches where you plan to place it.

What you get

• Skull and wing Graphic die-cut to shape with no background box
• Printed on flexible Cast Vinyl that conforms to helmet curves
• Available in 4, 8, 12 or 18 inch decal sizes
• Choice of matte or gloss finish
• Premask layer keeps fine wing details aligned during application
• Suitable for helmets, tanks, fairings and other smooth surfaces
• Contour-cut edges resist lifting once pressed down

Specifications

Frequently asked questions

What size should I choose for my helmet?

A 4 or 8 inch decal fits well on the side of most helmets. Choose 12 or 18 inches if you are covering a full-face shell, a tank or another large flat surface. Measure your spot before ordering.

Will this decal stick to a curved helmet shell?

Yes. The Cast Vinyl is thin and flexible, and the premask layer helps you work it over gentle curves. Go slow near vents and edges, pressing from the center outward.

Can I remove the decal later?

Yes. Warm the decal gently with a hair dryer and peel it away slowly at a low angle. Any leftover adhesive can be cleaned off with isopropyl alcohol on a soft cloth.