Camo Tears Boat Decals Set of 2 Vinyl

Camo Tears Boat Decals Set of 2 | Camo Vinyl Graphics

A set of two camo tear graphics cut from durable vinyl, made for anglers and hunters who want their boat to stand out on the water. Available in widths from 12 to 48 inches.

Free shippingUSA: 5-7 days. International: 10-12 days.

Four finishesMatte, gloss, static cling or clear vinyl.

Made to orderNo returns for change of mind. Damaged orders are refunded or replaced.

Custom artworkUpload a sketch, logo or photo before adding to cart.

Size

Clear

Have your own design? Optional

Upload a logo, sketch or photo

JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.

Description

A set of two camo tear graphics cut from durable vinyl, made for anglers and hunters who want their boat to stand out on the water. Available in widths from 12 to 48 inches.

Camo Decals That Bring Personality to Your Boat

These tear-shaped camo graphics give your boat a worn, weathered look that pairs naturally with hunting and fishing setups. Each order includes two matching decals, so you can mirror them on both sides of the hull for a balanced appearance. The rip design reads like the camo is tearing away to reveal what is underneath, which adds depth and character without overwhelming your boat's existing paint or wrap. Whether you run a bass rig, a duck boat, or a jon boat, this graphic works as a simple way to make an ordinary hull feel like yours. Choose the width that fits your space, apply both pieces, and get back on the water the same day.

Cut Vinyl Built for Marine Use

Each tear graphic is precision cut from cast vinyl, a material chosen for its ability to conform to the curves of a boat hull without lifting at the edges. The vinyl resists water, sun, and routine cleaning, holding its color through seasons of use on lakes, rivers, and coastal waterways. Matte, gloss, and clear finish options let you match the decal to your boat's surface, whether you want the graphic to blend with a flat paint job or add a subtle sheen over gel coat. Application tape keeps every piece of the detailed camo tear pattern aligned during install, so the fine edges land exactly where they should.

How to Apply Your Camo Tear Decals

Start with a clean, dry surface free of wax, grease, and loose dirt, since any residue under the vinyl can cause edges to lift over time. Position each decal with the application tape facing out, using small pieces of tape to hold it in place while you step back and check alignment from a distance. Once you are satisfied, peel the backing away, press the decal onto the hull working from the center outward, and use a squeegee or firm card to push out air and moisture. Slowly remove the application tape at a low angle, then go over the full graphic once more with firm pressure. Allow the vinyl to set before launching the boat.

Choosing the Right Size for Your Hull

This set is offered in widths from 12 to 48 inches, covering everything from small jon boats to full-size bass rigs and pontoon hulls. A 12-inch pair works well near the bow or beside a registration number, while 36 to 48-inch sets fill the broad sides of larger boats with a bold statement. Before ordering, measure the flat or gently curved area where you plan to place each decal and compare it to the listed width. Remember that the tear shape runs taller than it is wide, so check vertical clearance as well. If you are layering the graphic near other lettering or decals, leave a small gap so each element stays readable.

What you get

Set of two matching camo tear decals for both sides of your boat
Available in widths from 12 to 48 inches
Precision cut from cast vinyl for detailed edges
Matte, gloss, and clear finish options to match your hull
Conforms to curved boat surfaces without lifting at the edges
Includes application tape for accurate placement
Suitable for hulls, consoles, trailers, and tackle storage

Specifications

Material	Cast vinyl
Finish	Matte, gloss, or clear
Application	Dry application with included transfer tape; apply to a clean, wax-free surface
Set contents	2 camo tear decals (left and right placement), one per side

Frequently asked questions

Will these decals hold up in water and sun?

The cast vinyl used for these camo tear graphics is made to withstand water exposure, sunlight, and routine washing. Proper application to a clean surface is the biggest factor in how well the edges stay down over time.

Can I put these on a textured or heavily curved surface?

These decals apply best to smooth or gently curved surfaces such as gel coat, painted hulls, and smooth aluminum. Heavily textured surfaces may not allow the vinyl to fully adhere at the detailed edges.

Do I need to wait before putting my boat back in the water?

Yes. After applying the decals and removing the transfer tape, let the vinyl set before launching. This gives the adhesive time to bond so the edges stay secure when the hull gets wet.