MX Graphics Kit for Dirt Bike Helmets | Decal Set

Description

A dirt bike helmet decal kit printed on cast vinyl, sized to fit motocross and off-road helmets from 12 to 48 inches. Made for riders who want a fresh look without paying full custom-wrap prices.

What Comes in This Moto Sticker Set

Each kit arrives as a coordinated set of decals designed to work together on a standard dirt bike helmet. You get side panels, a front brow piece, chin section strips, and smaller accent decals for vents, edges, and the back of the shell. The layout follows the natural curves of most motocross helmets, so you are not fighting odd shapes or trimming oversized pieces to make them fit. Because the set is sold in width options from 12 to 48 inches, you can match the kit to your helmet size, from youth shells up to full-size adult helmets. Every piece is printed at the same time on the same material, so colors stay consistent across the whole set once it is applied to your lid.

Choosing the Right Size MX Graphics Kit

Sizing is the part most riders get wrong, so here is the simple approach. Measure the widest point of your helmet from side to side, usually across the cheek area, and compare that to the kit width options. A youth helmet typically pairs well with the smaller widths, while adult large and extra large shells usually need the mid to upper range. If you are between sizes, going up gives you material to trim at the edges, which is easier than stretching a piece that is too small. The decals are cut with a small margin so you can fine-tune the fit around vents and visor mounts. Take your time, dry-fit each piece before peeling the backing, and the panels will land where they should.

Matte, Gloss, and Clear Finish Options

This kit is printed on cast vinyl, which is thin and conforms to the curved surfaces of a helmet without lifting at the edges. You can choose the finish that matches your gear. Matte gives a low-sheen, modern look that hides fingerprints and scuffs from transport. Gloss adds depth and makes the colors pop under track lighting. Clear and static cling options are also available if you want a subtle overlay or a design you can reposition and remove without adhesive residue. All finishes are cut and packed together, so mixed finishes within one set are not offered, but each option uses the same printing process and the same cast vinyl base for a consistent result across every decal in the kit.

Applying Your Helmet Decals Step by Step

Start with a clean helmet. Remove the visor if you can, wash the shell with mild soap and water, and wipe it down with isopropyl alcohol to strip any wax or residue. Let it dry fully. Warm the decal slightly with a hair dryer or heat gun on low to soften the vinyl, then apply from the center outward, smoothing with a squeegee or your thumb to push air toward the edges. Poke any trapped bubbles with a pin and press them flat rather than lifting the piece. Work panel by panel, and keep the helmet at room temperature during application. Avoid riding or heavy handling for the first day so the adhesive sets. Applied this way, the decals sit flush and hold their edges.

What you get

• Complete decal kit for dirt bike and motocross helmets
• Width options from 12 to 48 inches to fit youth through adult shells
• Printed on cast vinyl that conforms to curved helmet surfaces
• Available in matte, gloss, static cling, and clear finishes
• Coordinated side, brow, chin, and accent pieces in one set
• Cut with trim margin for fitting around vents and visor mounts
• Made to order in our US shop

Specifications

Frequently asked questions

Will this kit fit my specific helmet model?

The kit is not model-specific. It is cut to work with the general shape of motocross and off-road helmets, and the width options let you match your shell size. Measure across the widest point of your helmet and choose the closest kit width, going up if you are between sizes.

Can I remove the decals later?

Yes. Warm the decals with a hair dryer and peel slowly from one edge. Static cling and clear finishes remove without adhesive residue. For the adhesive-backed finishes, any leftover residue can be cleaned with isopropyl alcohol.

Can I mix finishes within one kit?

Each set is printed in a single finish, so matte, gloss, static cling, and clear cannot be combined within the same kit. Pick the finish you want at checkout and every decal in the set will use it.