Rear Fender Decal Set | Dirt Bike MX Graphics Kit

Description

A rear fender graphics decal set for dirt bikes, printed on durable cast vinyl in your choice of matte, gloss, clear or static cling finish. Made for riders who want to refresh or customize the back of their bike.

Rear Fender Decals Built for the Track and the Trail

The rear fender takes more abuse than almost any other panel on a dirt bike. Mud, roost, boot heels and tip-overs all land right there, which is why a dedicated rear fender decal set is one of the most practical pieces of any mx graphics kit. Our rear fender graphics are printed on cast vinyl that conforms to the curves of plastic fenders without lifting at the edges. You choose the finish, matte for a low-key factory look, gloss for a showroom shine, clear to layer over an existing color scheme, or static cling for a temporary, residue-free option. Each set is cut to order in your choice of width from 12 to 48 inches so it fits small-bike fenders up to full-size motocross plastic.

Choose Your Width and Finish

Every rear fender is a little different, so we sell this decal set by width. Pick 12 or 18 inches for youth bikes and mini fenders, 24 or 30 inches for most 125 to 250 class machines, and 36 to 48 inches if you are covering a wide flat fender or wrapping the shape end to end. Material is available in four finishes only: matte, gloss, clear and static cling. Matte hides scuffs and fingerprints well and pairs nicely with darker plastics. Gloss pops in photos and under stadium lighting. Clear lets your fender color show through the printed artwork. Static cling applies without adhesive and peels off clean, which makes it a smart pick for race-day only setups or borrowed bikes.

How to Apply Rear Fender Graphics

Start with a clean fender. Wash off mud and chain lube, then wipe the application area down with isopropyl alcohol and let it dry fully. Warm the decal slightly with a hair dryer or heat gun on low so the vinyl relaxes into the fender's contour. Apply from the center outward, using a squeegee or the edge of a card to push air toward the edges. If you trap a bubble, pierce it with a pin and smooth it flat. For curved sections, stretch gently and keep the heat moving. Static cling versions skip the alcohol prep, just mist the fender with soapy water, position the decal, and squeegee the water out. Wait a full day before washing the bike so the adhesive sets.

Why Riders Order From LEO Sticker

We print every rear fender decal set in-house on cast vinyl using fade-resistant inks, so your design stays sharp through sun, mud and pressure washing. Because each order is cut to your chosen width, you are not trimming a universal sheet down to size and hoping the artwork still lines up. Our team rides too, so we know what happens to graphics that get installed crooked or peel at the edges, and we cut with a small overlap margin to help prevent both. If you are building a full mx graphics kit, this rear fender set pairs with our other dirt bike decal listings so the whole machine carries one consistent look. Questions on sizing? Send us your fender width before ordering and we will point you to the right option.

What you get

• Rear fender decal set for dirt bikes and motocross machines
• Available in 12, 18, 24, 30, 36, 42 and 48 inch widths
• Four finish options: matte, gloss, clear and static cling
• Printed on cast vinyl that conforms to curved fender plastic
• Fade-resistant inks hold up to sun, mud and washing
• Cut to order for a clean fit without trimming guesswork
• Static cling version removes clean with no adhesive residue

Specifications

Frequently asked questions

How do I pick the right width for my rear fender?

Measure straight across the widest part of your rear fender where you want the graphic to sit. Choose the width option that matches or slightly exceeds that measurement so you have a little material to work with at the edges.

Will these decals damage my stock plastic?

Our adhesive vinyl is designed to remove without damaging plastic when peeled warm. Our static cling option uses no adhesive at all and lifts off clean, which is the safest choice if you plan to remove graphics often.

Can I wash my bike after applying the decals?

Wait about 24 hours after installation before washing so the adhesive fully bonds. After that, normal washing including a gentle pressure spray from a distance is fine. Avoid aiming a high-pressure nozzle directly at the decal edges.