By vehicle
By style
By position
Guides
Marine & water
Powersports
Storefront & office
Labels & packaging
Bulk & wholesale
Send your own artwork
Upload your logo or sketch on any product page: we cut it in the width you choose.
Shop
Kids & anime
Sports & fan
Custom stickers
Start here
Your design, our vinyl
Send a sketch or logo, optional upload box sits under the size selector on every product.
Finishes we print
Sizes we cut
12"18"24"36"48"
Your tablet travels everywhere: backpack, kitchen counter, gym bag, airplane tray table. That daily handling is exactly why standard paper stickers peel, curl, and leave sticky patches on the back of an iPad or Galaxy Tab.
Showing the single result
Your tablet travels everywhere: backpack, kitchen counter, gym bag, airplane tray table. That daily handling is exactly why standard paper stickers peel, curl, and leave sticky patches on the back of an iPad or Galaxy Tab. This collection gathers small-format vinyl decals and skins cut for tablets, with removable adhesive that holds through daily use and peels off clean when you want a change. Whether you are covering scuffs on a used device, adding grip texture to a slippery back panel, or personalizing a tablet that goes to school or work, these are sized and cut for the job rather than trimmed down from laptop sheets.
This collection covers two product types: full or partial skins cut to match specific tablet back panels, and smaller individual decals sized for tablets rather than laptops. Within that, you will find camera and port cutout skins, edge wrap pieces, corner accent decals, and small-format art stickers sized under 4 inches.
It suits students decorating a personal iPad, remote workers marking a company tablet so it stops getting mixed up at meetings, families labeling kids' tablets for school, and anyone reselling or refreshing a used device. If you need matching decals for other gear, sibling collections in this silo cover phone stickers, keyboard stickers, controller skins, AirPods skins, and laptop stickers.
Most tablet skins use cast vinyl because it is thin, conforms to slight curves around tablet edges, and removes cleanly. Calendered vinyl works for flat back-panel decals and costs less, but it is thicker and less forgiving on curved corners.
Common materials you will see listed on product pages:
Finish options typically include gloss with a gloss laminate for scratch resistance and matte for low glare under classroom or office lighting. Check each listing, since not every design is stocked in every finish.
Tablet back panels vary a lot, so measure before ordering. Common tablet sizes and their approximate screen diagonal versus back panel width:
Full skins are cut about 0.25 inch short of each edge so you have room to position without overhanging. Camera cutout skins list the exact camera cluster dimensions, and port cut pieces note whether they fit a centered or corner USB-C position.
For individual decals, anything from 1.5 to 4 inches works well on a tablet back. Anything larger starts competing with a case or camera cutout. If you use a folio case, place decals only on exposed areas and confirm the skin thickness, since laminated pieces around 6 mil total can bind in some tight case edges.
Steps for a clean application:
For care, wipe with a damp cloth and mild soap. Skip solvents on printed finishes. To remove, warm the skin with a hair dryer on low, peel from a corner at a shallow angle, and roll off any remaining adhesive with your thumb. Removable adhesive leaves no residue when removed within its rated life, so check the product page for the stated window.
A short decision list:
The skins and decals in this collection use removable adhesive. When removed within the stated adhesive life, typically several years, they peel off without leaving residue. If a skin has been on for a long time, warm it with a hair dryer on low and peel slowly at a shallow angle. Any leftover adhesive rolls off with a thumb or a small amount of isopropyl alcohol on a cloth.
Full-panel skins include a camera cluster cutout, and product pages list the exact cutout dimensions and position so you can match them to your device. Port coverage varies by design, since USB-C placement differs between models. Measure your camera cluster and port position against the listed dimensions before ordering.
Most skins are cut about 0.25 inch short of the panel edge, which keeps them inside typical case margins. Very tight folio edges can bind on thicker laminated pieces around 6 mil total. If your case fits closely, choose an unlaminated cast vinyl skin or place individual decals only on exposed areas.
You can trim a skin with a sharp craft knife along the panel edge, but cutout positions will not move. If your camera cluster sits in a different corner, a trimmed skin will not line up. For a device we do not list directly, choose individual decals under 4 inches instead, since they do not depend on cutout alignment.
Orders ship from our US facility, and production time is listed on each product page before shipping transit. Transit time depends on the shipping option you choose at checkout. If you need a skin by a specific date, such as a gift or the start of a school term, check the stated production window and choose a faster shipping method at checkout.
Matte finishes hide fingerprints and fine scratches better than gloss, and they cut glare under classroom and office lighting. Gloss with a gloss laminate is more scrub resistant for high-touch or kid use but shows smudges. Static cling applies without adhesive and can be repositioned, so it suits windows and smooth surfaces that need a clean removal.
Your shopping cart is empty
Notifications
