By vehicle
By style
By position
Guides
Marine & water
Powersports
Storefront & office
Labels & packaging
Bulk & wholesale
Send your own artwork
Upload your logo or sketch on any product page: we cut it in the width you choose.
Shop
Kids & anime
Sports & fan
Custom stickers
Start here
Your design, our vinyl
Send a sketch or logo, optional upload box sits under the size selector on every product.
Finishes we print
Sizes we cut
12"18"24"36"48"
You pull your phone out fifty times a day, so the back of it might as well look the way you want. Phone stickers are small-format vinyl decals sized to fit flat areas on phones, cases, and pop-socket bases without covering cameras, buttons, or wireless charging coils.
Showing all 3 resultsSorted by popularity
You pull your phone out fifty times a day, so the back of it might as well look the way you want. Phone stickers are small-format vinyl decals sized to fit flat areas on phones, cases, and pop-socket bases without covering cameras, buttons, or wireless charging coils. Because they use removable adhesive, you can swap designs when a season or mood changes and peel the old one off clean. This collection sits within our laptop and tech sticker lineup, alongside AirPods skins, controller skins, and keyboard stickers, for people decorating their whole gear setup in one order.
This collection covers die-cut phone decals, small logo and art stickers, and partial skins meant for the back panel of a phone or a flat case. Sizes typically run from about 0.75 inches up to 3 inches on the longest side, which is the range that fits most phone backs without wrapping around edges or interfering with camera bumps.
It suits three groups: people who want a single statement decal on a clear case, people covering a matte case with a cluster of small stickers, and gift buyers assembling a pack. If you need full-coverage wraps that go edge to edge, those are a different product. These are stickers you place and reposition, not precision-cut full skins.
Most small-format phone decals are cut from calendered vinyl, which is about 2.5 mil thick and available in a wide color range. Cast vinyl is thinner and conforms better to slight curves, which matters if you are placing a sticker near a curved case edge. Cast films are also a common choice for outdoor use.
Some listings use an air-release liner, which lets you smooth out trapped bubbles during application. Removable adhesive is standard across this collection so removal stays clean.
Measure the flat area before ordering. A typical phone back has roughly 2.5 by 5 inches of usable flat space, minus the camera module, which on many current models takes a 1.5 to 2 inch square in a corner.
Practical sizing guidance:
On textured or silicone cases, adhesive bonds poorly. Place stickers on the phone itself or on a smooth hard case. Stickers placed over the wireless charging coil area, roughly the center of the back, generally do not affect charging since vinyl is non-printed, but thick layered clusters can be an issue with some printed mounts.
Steps for a clean application:
For care, avoid submerging the phone or running it under water for the first 24 hours while the adhesive sets. Wipe stickers with a damp cloth rather than alcohol, which can haze gloss finishes. To remove, lift a corner with a fingernail and peel slowly at a low angle. Warm the vinyl slightly with a hair dryer on low if it resists. Any residue can be rolled off with your thumb or a small amount of adhesive remover on a cloth.
A short decision list:
If you are decorating more than your phone, our Laptop Stickers and AirPods Skins collections use the same removable adhesive system, so you can coordinate a matching set.
No. This collection uses removable adhesive, so peeling the sticker off slowly leaves the surface clean. If a sticker has been on for a year or more, warm it with a hair dryer on low first, then peel at a low angle. Any leftover adhesive rolls off with a fingertip or a small amount of adhesive remover on a cloth.
Not reliably. Vinyl adhesive needs a smooth surface to bond, and silicone and soft-touch textured cases resist adhesion. Apply stickers directly to the phone back or to a smooth hard case made of polycarbonate or TPU with a glossy or matte flat finish. Textured areas will cause edges to lift within days.
Measure the flat area of your phone back first, then subtract the camera module. Most phones have about 2.5 by 5 inches of flat space. A 2 to 3 inch decal works as a centerpiece, while clusters of 1 to 1.5 inch stickers fill remaining space. Keep stickers at least a quarter inch inside case edges so the rim does not lift them.
A single standard vinyl sticker is non-printed and thin enough that wireless charging generally works normally. Problems arise with thick layered clusters or metal-look finishes placed over the charging coil area. If you use a printed mount or MagSafe charger daily, keep the center of the phone back clear or use one thin sticker there.
We do not recommend it. Cut around the camera module instead, leaving at least an eighth inch of clearance around the lens housing. Sticker material over lenses blocks photos, and edges near the raised camera ring lift quickly from friction in a pocket. Small stickers placed below or beside the module last much longer.
Orders ship from our US facility, typically within one to three business days. Delivery takes 5 to 7 days in the United States. If you are ordering for a gift or event, allow extra time for production during peak periods, and check the listing for current handling times before ordering.
Your shopping cart is empty
Notifications
