By vehicle
By style
By position
Guides
Marine & water
Powersports
Storefront & office
Labels & packaging
Bulk & wholesale
Send your own artwork
Upload your logo or sketch on any product page: we cut it in the width you choose.
Shop
Kids & anime
Sports & fan
Custom stickers
Start here
Your design, our vinyl
Send a sketch or logo, optional upload box sits under the size selector on every product.
Finishes we print
Sizes we cut
12"18"24"36"48"
Your console sits in the living room where everyone sees it, so the plain factory finish stands out for the wrong reason. This collection of gaming console stickers covers small-format vinyl skins and decals sized for current and recent-generation PlayStation, Xbox and Nintendo hardware.
Showing all 2 resultsSorted by popularity
Your console sits in the living room where everyone sees it, so the plain factory finish stands out for the wrong reason. This collection of gaming console stickers covers small-format vinyl skins and decals sized for current and recent-generation PlayStation, Xbox and Nintendo hardware. Each piece is cut to fit around vents, disc slots, USB ports and fan intakes, so airflow and button access stay intact. The adhesive is removable, which matters if you rent, resell consoles, or rotate designs between seasons. Application takes minutes with a hair dryer and a squeegee or credit card, and removal later leaves no residue to scrape off the shell.
This collection includes full-console skins, partial decals for top plates and dock lids, and small accent stickers for controllers, docks and carrying cases. Common targets are the PS5 faceplates and midplate, Xbox Series X and S side panels, Switch console backs, Switch OLED dock sides and Joy-Con rails.
The typical buyer is a console owner who wants personalization without opening the hardware or voiding service access. Parents use these to label consoles in multi-kid households. Streamers and content creators use them to match a setup color scheme on camera. Resellers apply neutral skins to cover light scuffing before listing a used unit. Because the adhesive is removable, none of these uses are permanent commitments.
Most console stickers in this collection are printed on cast vinyl, which is thin enough (around 2-3 mil before laminate) to conform to the slight curves on console shells without lifting at the edges. Calendered vinyl appears on some budget options; it is thicker and less conformable, so it suits flat panels like the Switch dock rather than curved Joy-Con rails.
Where listed, you may see calendered gloss vinyl (a common choice for decals), cast vinyl with better conformability, or cast wrap film on premium skins. Laminate options include gloss for a factory-like sheen and matte for a low-glare finish that reads well on stream.
Many full-body skins ship on an air-release liner, which channels trapped air out during application instead of leaving bubbles under the film.
Cut sizes are matched to specific console generations, so check the product listing against your exact model. Some reference dimensions to keep in mind:
Placement matters for heat. Never cover exhaust vents, intake grilles or the PS5 rear fan outlet. Listings note which areas are left exposed. If a decal slightly overlaps a vent edge, trim with a fresh craft knife before smoothing it down.
Follow these steps for a clean application:
For care, dust with a dry cloth and avoid solvent cleaners. To remove, warm the decal with a hair dryer and peel slowly at a low angle. Any leftover adhesive wipes off with isopropyl alcohol.
Work through this short list before ordering:
If you also want matching pieces, browse our Controller Skins and Keyboard Stickers collections in the same silo.
No, as long as vents and intakes stay open. Every design in this collection leaves exhaust and intake areas exposed, and the vinyl itself is thin enough that it does not trap meaningful heat against the shell. If you trim a decal yourself, keep it at least a quarter inch away from any vent opening so airflow is not restricted.
The adhesive is formulated for clean, residue-free removal. When you peel the decal slowly after warming it with a hair dryer, it lifts without pulling the factory finish. Any faint adhesive residue left behind wipes off with isopropyl alcohol on a microfiber cloth. Avoid aggressive scraping with metal tools.
Each listing states the compatible model, such as PS5 original, PS5 slim, Xbox Series X, Series S, Switch standard, Switch OLED, or Switch Lite. Panel dimensions vary between editions, so match your model rather than the brand alone. If your console is a special edition with a unique shell, measure the flat panel area in inches and compare it to the listed decal size.
Yes, within the first minute or two. Cast vinyl with an air-release liner can be lifted and re-aligned if you have only lightly pressed it down. Once you have squeegeed the full surface and heated the edges, repositioning is no longer practical. Align the cutouts over ports or the disc slot first, since those are your fixed reference points.
Our printed vinyl is offered in matte, gloss, static cling and clear finishes, with no laminate layer applied. Consoles in direct sunlight or near heat sources may show wear sooner, since heat and light can affect printed vinyl over time. Matte and gloss finishes are both smooth printed surfaces, so a skinned console can be dusted and handled gently like any vinyl skin.
Yes, we ship to all US states. Small-format decals and skins ship as standard letter or lightweight parcel mail, so shipping is inexpensive and tracking depends on the service level chosen at checkout. Orders with multiple skins or larger decal sets are packed flat to prevent creasing during transit.
Your shopping cart is empty
Notifications
