Ram & Dodge Challenger Decals

Ram trucks and Dodge Challengers attract two very different decal audiences, and this collection covers both. Ram owners usually want graphics that work with a long body: tailgate lettering, bed side stripes, rocker panel accents and hood overlays. Challenger owners tend to look for stripes that follow the muscle car proportions, along with door decals and smaller accents for fenders or windows. Because a full size pickup and a two door coupe share almost no panel dimensions, sizing is the single most important step before ordering. Every decal here is cut from vinyl you can trim to fit, but starting with the right size range saves time and material. Measure each panel before you buy.

Popular Placements on These Vehicles

On Ram pickups, the most requested placements are the tailgate, the bed sides, the rocker panels below the doors, and the hood. Tailgate decals work well because the surface is flat and large. Bed side graphics run along the length of the box and suit long stripe designs. On Challengers, owners most often apply hood stripes, dual racing stripes running from nose to trunk, door decals, and rear window accents. The wide, flat hood is a natural canvas, and the rear quarter panels take smaller badge style decals well.

Sizing, Fit and Placement for Ram and Dodge Challenger Decals

Measure the panel before ordering. For a pickup tailgate, decals in the 30 to 60 inch width range are common, depending on whether you want lettering only or a full width graphic. Bed side stripes typically fall between 40 and 70 inches long. Rocker panel decals usually run 50 to 80 inches per side on a crew cab. For Challenger hoods, stripe sets between 20 and 40 inches wide cover most layouts, while full length racing stripes are often ordered in the 60 to 90 inch range to span hood to trunk. Door decals for the Challenger commonly land in the 12 to 24 inch width range. These are ranges only, so confirm your own measurements.

Materials Behind Ram and Dodge Challenger Decals

Both vehicles spend time in sun, road grime and car washes, so the vinyl matters. For horizontal surfaces like truck hoods and Challenger hoods or trunk lids, a calendared or cast vinyl rated for outdoor use holds up better against sun damage. Cast vinyl is thinner and conforms to curves, which helps on Challenger fenders and quarter panels. For flat truck panels such as tailgates and bed sides, calendared vinyl is a practical choice. Laminate or matte finishes cut down shine on long hood stripes. Avoid household craft vinyl for anything mounted outside.

Installation Notes for These Body Styles

Start with a clean, dry, wax free surface. On Ram bed sides, work from the front of the bed toward the tailgate so you can squeegee along the panel without reaching over applied vinyl. Tailgate applications go fastest with the gate closed and flat. On the Challenger, the long hood stripe is easiest applied in sections with a center reference line marked with low tack tape. Curved quarter panels need heat and patience, so stretch the vinyl slightly rather than forcing it flat. Keep the vehicle above roughly 60 degrees Fahrenheit during application, and wait several days before pressure washing.

Related collections

Frequently asked questions

Will one decal size fit both my Ram and my Challenger?

No. A full size pickup and a two door coupe have very different panel lengths and heights. A tailgate graphic will not suit a Challenger trunk lid, and hood stripes sized for a coupe will look undersized on a truck hood. Order separate decals measured for each vehicle and each specific panel.

How do I measure my truck bed side for a stripe?

Use a tape measure along the flat section of the bed side, from the front edge near the cab to the tailgate. Note the height available between body lines as well. Order a decal slightly smaller than your smallest measurement so you have room to position it without wrapping onto adjacent panels.

Can I apply hood stripes to a Challenger by myself?

Yes, with preparation. Mark the hood center line with low tack tape, apply the decal in sections, and use a squeegee from the center outward. A second person helps keep long stripe sets aligned. Work in a shaded area above 60 degrees Fahrenheit so the vinyl stays flexible.

Do these decals damage paint when removed?

Quality vinyl removed with heat generally comes off cleanly from factory paint in good condition. Warm the decal with a hair dryer or heat gun on a low setting and peel slowly at a shallow angle. Any remaining adhesive can be cleaned with an adhesive remover safe for automotive paint.