Tumbler Vinyl Sticker Decals for Cups & Tumblers | LEO

Description

Matte and gloss vinyl decals cut for tumblers, water bottles, and cups. Made for crafters, small shops, and anyone who wants a clean decal that holds up outdoors.

A Vinyl Sticker Built for Tumbler Life

Tumblers go everywhere: cup holders, gym bags, car dashboards, and the dishwasher rack on a bad day. This vinyl sticker is cut from durable cast vinyl with a matte or gloss finish, so it sits flat against curved walls without lifting at the edges. The low-sheen matte option reads like a painted-on design, while gloss adds a crisp, clean pop against stainless or powder-coated surfaces. Each set includes multiple size options, so you can fit a tall 30 oz tumbler, a slim bottle, or a short coffee cup from the same order. Choose your width from 12 to 48 inches and we cut your set to match.

Sizing Your Decal to the Curve

Getting the right size matters more on a tumbler than on a flat panel, because a decal that is too wide will fight the taper near the top of the cup. As a general guide, measure the straight section of your tumbler wall and pick a width that leaves a little breathing room on each side. Our 12 to 48 inch width options cover everything from small 8 oz cups to oversized 40 oz travel tumblers. Because every set includes more than one size, you can test placement with a smaller piece before committing to the larger cut. If you apply multiple decals, keep spacing even so the design wraps naturally around the curve.

Application Without Bubbles or Creases

Start with a clean, dry surface; wipe the tumbler with rubbing alcohol and let it fully dry, especially if it has a powder-coat finish. Peel the backing slowly, line up one edge first, and press from the center outward with a squeegee or the edge of a card. Working from the middle keeps air pushing toward the sides instead of trapping it under the vinyl. On tight curves, warm the decal slightly with a hair dryer so it flexes into the shape, then hold it in place for a few seconds. Wait about 24 to 48 hours before washing or heavy handling so the adhesive bonds fully to the surface.

Care Tips for Long-Lasting Decals

Once applied, treat your tumbler decal the way you would treat the finish underneath. Hand washing with mild soap is the gentlest option and helps the edges stay sealed. If the tumbler must go in the dishwasher, top rack placement and a gentle cycle are easier on the vinyl than high-heat settings. Avoid scrubbing directly over the decal with abrasive pads, and skip soaking the whole cup for long periods. For outdoor use on bottles that ride in bike cages or car cup holders, the durable vinyl holds up against sun, rain, and everyday scuffs. If you ever want to remove it, warm it gently and peel slowly; any residue comes off with adhesive remover.

What you get

• Cut from durable cast vinyl in matte or gloss finish
• Set includes multiple size options with widths from 12 to 48 inches
• Fits straight and gently curved tumbler, bottle, and cup walls
• Matte option reads painted-on; gloss adds a clean shine
• Water-resistant for outdoor use on bottles and travel tumblers
• Bubble-free application with included transfer tape
• Made to order in our US shop

Specifications

Frequently asked questions

Will these decals stick to powder-coated tumblers?

Yes. Clean the surface with rubbing alcohol first and let it dry completely. Powder-coat has a slight texture, so press firmly from the center outward and give the adhesive 24 to 48 hours to fully bond.

What size should I choose for a 30 oz tumbler?

Measure the straight, flat section of the tumbler wall rather than the total circumference, then choose a width slightly smaller than that measurement. Our 12 to 48 inch width options cover most standard tumbler sizes.

Are these decals dishwasher safe?

Hand washing is the gentlest option and helps the edges stay sealed. If you use a dishwasher, place the tumbler on the top rack with a gentle cycle, and avoid high-heat settings and abrasive scrubbing over the decal.