Truck Bed Decals | Cast Vinyl Bed Stripe Set for Pickup

Description

A set of truck bed decals cut from cast vinyl, made for pickup owners who want a clean stripe accent along the bed rails. Offered in 12" to 48" widths with a choice of matte, gloss, or clear finish.

Cast Vinyl Truck Bed Decals Built for Daily Use

These truck bed decals are cut from cast vinyl, a thin, flexible film that conforms to the slight curves and body lines along a pickup bed. Cast vinyl is the same film type used for professional vehicle graphics because it holds its shape around contours without lifting at the edges. Each set is trimmed as a pair of matching stripes, so you get a balanced look on both sides of the bed. Choose matte for a low-sheen, painted-on look, gloss for a shine that reads like a factory stripe, or clear for a subtle protective accent. Widths run from 12 inches up to 48 inches, so you can match the stripe to the proportions of your bed rails and tailgate area.

Choosing the Right Width for Your Bed Stripes

Stripe width changes the whole personality of the truck. A 12-inch or 16-inch set sits closer to the bed rail and reads as a subtle accent, while 24-inch and 32-inch widths create the broad racing-style band many pickup owners want. The 40-inch and 48-inch options cover more of the bed side panel for a bold, two-tone effect. Before ordering, measure the flat area between your bed rail and any body line or molding, then pick the width that fits inside that space with room to spare. Because the vinyl is cut to your selected width, a quick tape-measure check before checkout saves trimming work during installation.

How to Install Your Truck Bed Decal Set

Installation works best on a clean, dry surface above about 60 degrees Fahrenheit. Wash the bed panel thoroughly, remove any wax with isopropyl alcohol, and let the area dry completely. Position each stripe with masking tape as a hinge, peel a portion of the backing, and squeegee from the center outward to push air toward the edges. Work in small sections rather than peeling the whole backing at once. The cast vinyl stretches slightly around gentle curves, so apply light heat from a hair dryer if you need extra flex near body lines. Wait about 24 to 48 hours before pressure washing so the adhesive fully bonds to the paint.

Caring for Matte, Gloss, and Clear Bed Decals

Once installed, these truck bed decals need very little attention. Wash them with the same mild soap you use on the rest of the truck, using a soft cloth or wash mitt rather than a stiff brush. Skip high-pressure nozzles pointed directly at the stripe edges, especially in the first few days after application. For gloss and clear finishes, a light automotive spray wax keeps the film looking consistent with the surrounding paint. Matte finishes should stay away from wax, since it can create shiny patches; a matte-safe detail spray is the better choice. If you ever want to remove the stripes, warm them gently and peel slowly, then clean off any adhesive residue with an automotive adhesive remover.

What you get

• Cut from cast vinyl that conforms to bed rail curves and body lines
• Sold as a matching set for both sides of the truck bed
• Available in 12", 16", 24", 32", 40", and 48" widths
• Choose matte, gloss, or clear finish
• Matte finish reads like painted stripes; gloss adds a shine similar to factory striping
• Outdoor-grade adhesive intended for pickup truck exteriors
• Removable with gentle heat and slow peeling

Specifications

Frequently asked questions

Will these truck bed decals fit my specific pickup model?

The stripes are cut to your selected width rather than to any one vehicle, so they are not model-specific. Measure the flat area along your bed panel and choose a width that fits within it. Most full-size and mid-size beds have room for at least the narrower widths.

What is the difference between matte, gloss, and clear?

Matte has a flat, low-sheen look similar to painted stripes. Gloss has a shiny finish that reflects light like factory striping. Clear is transparent and works as a subtle accent or protective layer over an area you want to keep visible.

Can I install these myself, or do I need a shop?

Most customers install them at home with a squeegee or credit card, masking tape, and a hair dryer for curves. Working in small sections and keeping the surface clean makes the process straightforward. A second pair of hands helps with the wider 40-inch and 48-inch stripes.