Colorado Tailgate Decals for Trucks, Matte Vinyl Set

Description

Matte black vinyl tailgate decal set sized for midsize truck beds, cut to sit along the tailgate edge. Made for owners who want a clean, low-shine look without paint or permanent changes.

A Tailgate Decal Set Built for Midsize Trucks

This decal set is cut with midsize truck tailgates in mind, including the Chevrolet Colorado and GMC Colorado. The pieces follow the tailgate's horizontal lines, so the decal reads as part of the truck rather than a sticker slapped on top. Choose 4, 8, 12 or 18 inch sizes depending on whether you want a subtle accent or a bold statement across the whole panel. Each set is cut from matte Cast Vinyl that lays flat and conforms to the slight texture of factory paint. Application takes minutes with a squeegee or credit card, and the low-tack adhesive holds through washes and weather while still peeling clean when you are ready for a change.

Why Matte Black Works on a Tailgate

A matte finish absorbs light instead of bouncing it back, which gives the tailgate a uniform, shadowed look that pairs well with blacked-out trim, bed rails and window tint. On lighter paint colors, the contrast is sharp and Graphic. On darker trucks, the decal blends into a near-monochrome theme. Because there is no gloss, fingerprints, dust and water spots do not stand out the way they do on shiny surfaces. The matte calendered vinyl we print on also resists the everyday grime a working tailgate collects, from job-site dust to road spray. If you want a finish with more shine, the same set is available in gloss, and a clear version keeps your paint fully visible.

Chevrolet Decals for Tailgate Panels, Cut to Size

Our chevrolet decals for tailgate collection is organized around fitment and scale, and this set is one of the most ordered options in it. The 4 inch size works as a corner accent near the taillight. The 8 inch size sits well along the lower tailgate crease. The 12 inch size fills the space between the handle and the edge, and the 18 inch size spans most of the panel for full-coverage styling. Measure your tailgate before ordering, since trim packages and bed liners can change the flat area available. Every set ships with transfer tape applied, so the pieces go down as one unit with no letter-by-letter alignment.

Install, Remove and Reorder with Confidence

Start with a clean, dry tailgate and a mild soap solution if you want slide-to-position placement. Press from the center outward to push out air, then pull the transfer tape back on itself at a low angle. The vinyl can be lifted and repositioned while wet, so a first-time installer can get it straight. Removal is just as simple: warm the decal with a hair dryer and peel slowly, leaving adhesive residue you can roll off with a finger. If you are styling the whole truck, pair this set with matching tail light surrounds or a tailgate overlay from the same collection so the finish and cut lines stay consistent across the back of the vehicle.

What you get

• Matte black Cast Vinyl cut for midsize truck tailgates
• Available in 4, 8, 12 or 18 inch decal sizes
• Low-tack adhesive for clean removal without residue
• Pre-masked with transfer tape for one-piece installation
• Conforms to factory paint texture and slight panel curves
• Pairs with gloss, clear and static cling finishes from the same line
• Made in the USA and shipped flat to prevent creasing

Specifications

Frequently asked questions

Will this decal set fit my truck's tailgate?

The set is cut for midsize truck tailgates, including the Chevrolet Colorado and GMC Colorado. Measure the flat area of your tailgate and compare it to the 4, 8, 12 or 18 inch size options before ordering, since trim and bed liner setups vary. Not affiliated with or endorsed by the manufacturer.

Can I take it off later without damaging the paint?

Yes. Warm the decal with a hair dryer and peel it back slowly at a low angle. Any leftover adhesive can be rolled off by hand. We recommend applying to factory paint or fully cured repaints rather than fresh paint.

How long does installation take?

Most installs take under fifteen minutes. Clean the tailgate, position the pre-masked decal, squeegee from the center outward, then remove the transfer tape at a low angle. A spray of mild soap solution lets you slide the decal into position before it grabs.