Custom Cataclysm Stripe Car Decals, Set of 2

Cataclysm Stripe Car Decals, Set of 2 Custom Car Graphics

A pair of aggressive cataclysm-style stripe decals cut from cast vinyl, made for drivers who want bold car graphics on doors, hoods or tailgates. Choose your width from 12 to 48 inches to fit your build.

Free shippingUSA: 5-7 days. International: 10-12 days.

Four finishesMatte, gloss, static cling or clear vinyl.

Made to orderNo returns for change of mind. Damaged orders are refunded or replaced.

Custom artworkUpload a sketch, logo or photo before adding to cart.

Size

Clear

Have your own design? Optional

Upload a logo, sketch or photo

JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.

Description

Bold Stripe Graphics That Match Your Ride

This two-piece cataclysm stripe set brings a sharp, angular look to cars and trucks without the cost of a full wrap. The layered slash design works on door panels, rear quarters, hoods and tailgates, giving your vehicle a race-inspired edge. Because each stripe is cut to order in your choice of width, you can scale the graphic to suit a compact car or a full-size truck bed. Pair it with other custom car decals from our shop to build a coordinated theme, or run it alone as a single statement piece. Every set ships as mirrored left and right pieces so both sides of your vehicle match.

Choose Your Finish and Width

Each set is printed on your choice of matte, gloss, clear or static cling vinyl. Matte gives a painted-on look that blends into factory paint, gloss adds shine that stands out at car meets, clear lets your paint color show through the stripe outline, and static cling offers a temporary hold you can reposition or remove anytime. Widths run from 12 inches up to 48 inches, so measure your panel before ordering to get the coverage you want. The vinyl is cut cleanly with application tape in place, so the stripe transfers as one piece instead of dozens of small fragments you have to align by hand.

Applying Your Cataclysm Stripes

Start with a clean, dry, wax-free surface and work in moderate temperatures away from direct sun. Peel the backing, position the stripe using the application tape as a carrier, and squeegee from the center outward to push out air. Slowly remove the tape at a low angle and press the edges down firmly. The set includes mirrored pieces for both sides of the vehicle, and the vinyl conforms to gentle curves and body lines. If you are new to custom car decals, take your time with alignment before squeegeeing, since repositioning is easiest before firm pressure is applied. A heat source on your phone or a hair dryer can help the material stretch around tighter contours.

Care, Removal and Reordering

Wash around the decals by hand or with a gentle spray, avoiding high-pressure nozzles directly on the stripe edges. For permanent finishes, warm the vinyl before peeling it away in small sections; it lifts off in one piece rather than crumbling into scraps. Static cling pieces simply peel off with no residue, which makes them a good pick for leased vehicles or weekend shows. If you want to try a different width or finish later, reorder the same design in a new size. Keep a photo of your installed set so you can match placement when adding matching custom car decals down the road.

What you get

Set of 2 mirrored cataclysm stripe decals for left and right sides
Available in 12-inch to 48-inch widths to fit cars and trucks
Choice of matte, gloss, clear or static cling vinyl finish
Cut from cast or calendered vinyl with application tape for one-piece install
Conforms to gentle body curves and panel lines
Permanent finishes remove cleanly when warmed; static cling peels off residue-free
Printed to order in the USA by LEO Sticker

Specifications

Material	Cast or calendered vinyl, cut to shape
Finish	Matte, gloss, clear or static cling (select at checkout)
Application	Exterior vehicle panels: doors, hoods, quarters, tailgates
Set contents	2 mirrored stripe decals (left and right) with application tape, width selected at checkout

Frequently asked questions

How do I pick the right width for my vehicle?

Measure the panel area where you plan to install the stripe, such as the door or rear quarter, and choose the width that fits within that space. The 12-inch size suits compact cars, while larger widths work better on trucks and full-size doors.

Will these decals damage my paint?

When applied to clean, factory-cured paint and removed with gentle heat, the permanent finishes lift away without crumbling. Static cling offers a no-adhesive option that peels off with no residue, ideal for leased vehicles.

Can I use these stripes on a textured surface??

These decals adhere best to smooth, clean surfaces. Textured plastics and bed liners may not hold the vinyl securely, so we recommend smooth painted panels for the cleanest look.