Gloss Tailgate Stripe Decal Set for Trucks

Gloss Tailgate Stripe Decal Set for Dodge Ram Trucks

A gloss vinyl tailgate stripe decal set for truck owners who want a clean, finished look across the back of their pickup. Cut to order in four decal sizes so you can match the width of your tailgate.

Free shippingUSA: 5-7 days. International: 10-12 days.

Four finishesMatte, gloss, static cling or clear vinyl.

Made to orderNo returns for change of mind. Damaged orders are refunded or replaced.

Custom artworkUpload a sketch, logo or photo before adding to cart.

Size

Clear

Have your own design? Optional

Upload a logo, sketch or photo

JPG, PNG, WEBP or PDF, up to 20 MB. Leave this empty to order the design shown above.

Description

A gloss vinyl tailgate stripe decal set for truck owners who want a clean, finished look across the back of their pickup. Cut to order in four decal sizes so you can match the width of your tailgate.

A Tailgate Stripe Set That Finishes the Back of Your Ram

The tailgate is the part of your truck everyone sees at a stoplight, yet most stripe kits stop at the hood. This decal set was designed to bring the same gloss stripe treatment to the rear of your Ram, pairing naturally with our dodge ram hood decals if you want a matched front-and-rear look. Each stripe is cut from Cast Vinyl with a high-gloss surface that reads like painted striping once applied. The set is laid out to follow the horizontal lines of a full-size tailgate, so the stripes sit flat and level without trimming guesswork. Whether you run your truck daily or keep it for shows and weekend meets, this is a simple way to make the back end look deliberate instead of stock.

Gloss Cast Vinyl That Looks Painted On

We print and cut this set on Cast Vinyl with a gloss finish, chosen because it holds its shape over compound curves and edges without lifting or silvering. The gloss surface matches the sheen of factory paint closely enough that most people read the stripes as painted striping until they get within a few feet. Cast Vinyl also conforms around body lines and tailgate edges better than thicker films, which matters on a panel with ridges and contours. The adhesive is pressure-activated, so you can reposition each stripe during installation before pressing it down firmly. The result is a smooth, edge-to-edge finish with no visible carrier texture and no orange-peel effect under sunlight.

Four Decal Sizes to Match Your Tailgate Width

Every truck is set up differently, so this stripe set comes in four decal sizes: 4, 8, 12, and 18 inches. Measure the flat area of your tailgate between the tailgate lines before ordering, then choose the size that fits inside that space with a little margin on each side. Smaller sizes work well on trucks with backup cameras, Graphic, or handle recesses that eat into the panel, while the larger sizes suit wide, clean tailgates. The stripes arrive pre-spaced on transfer paper, so the gap between each stripe stays consistent without measuring each piece individually. If you are pairing this set with hood decals, ordering the same size for both keeps the stripe proportions consistent front to rear.

How to Install Your Tailgate Stripe Decals

Installation takes patience rather than skill. Start by washing the tailgate and removing any wax with isopropyl alcohol, then let the panel dry completely. Warm the decal slightly so the vinyl relaxes, and use the hinge method: tape one edge down, flip the decal back, peel the liner, and lay it down smoothly with a squeegee working from the center outward. Keep the stripes level by lining up the transfer paper edge with a body line before committing. Once everything is pressed down firmly, peel the transfer tape slowly at a low angle. Avoid washing the truck for the first couple of days so the adhesive fully bonds. Park in shade during installation for the easiest handling.

What you get

Gloss Cast Vinyl with a painted-on look that matches factory paint sheen
Available in 4, 8, 12, and 18 inch decal sizes
Pre-spaced stripes on transfer paper for consistent gaps
Pressure-activated adhesive allows repositioning during install
Conforms to tailgate body lines and edges without lifting
Pairs with hood stripe decals for a matched front and rear look
Cut to order in our US

Specifications

Material	Cast Vinyl
Finish	Gloss
Application	Exterior tailgate panel; pressure-activated adhesive, wet-free install with squeegee
Set contents	One tailgate stripe decal set on pre-spaced transfer paper, application instructions included

Frequently asked questions

Will these stripes fit my specific truck model?

The set is sold by decal size rather than by exact vehicle fitment. Measure the flat area of your tailgate and choose from the 4, 8, 12, or 18 inch options that fits within that space. Because the vinyl can be trimmed during installation, minor variations in tailgate layout are easy to work around.

Can I remove the stripes later?

Yes. Warm the vinyl with a hair dryer or heat gun on a low setting and peel it away slowly at a shallow angle. Any remaining adhesive can be cleaned off with isopropyl alcohol. Removal is easiest when the decals are warmed.

Can I pair this set with hood decals?

Yes, many customers run this tailgate set alongside our hood stripe decals for a matched look. Ordering the same decal size for both keeps the stripe proportions consistent from front to rear.