Shark Silhouette Boat Decals, Set of 2 Die Cut Vinyl

Description

A pair of shark silhouette decals cut from marine-ready vinyl, made for boat owners who want a bold predator shape on the hull, transom or cooler. Available in widths from 12 to 48 inches with matte, gloss, clear or static cling finishes.

Why a Shark Silhouette Works on Any Hull

A shark shape reads instantly from a distance, which makes it one of the most reliable designs for boat graphics. Whether you run a fishing boat, a pontoon or a center console, this silhouette adds attitude without cluttering the gelcoat. The clean outline pairs well with boat names, port letters or existing graphics, and it looks just as natural near the waterline as it does on the transom. Because the design is a simple filled shape, it stays legible even after salt spray, dock dust and a season in the sun. It is a low-effort way to give your boat a personality that matches the water you run it on.

Custom Die Cut Stickers Built for Saltwater Life

These are not printed rectangles with a shark picture inside. Each decal is die cut to the exact outline of the silhouette, so there is no background film or clear box left behind after application. We cut them from cast vinyl and calendered vinyl depending on the finish you select, and every decal is trimmed by plotter for crisp edges on the fins and tail. The set includes two sharks, so you can mirror them on both sides of the hull, stack them on the transom, or keep one as a spare. Choose matte for a painted-on look, gloss for shine that matches gelcoat, clear for a subtle effect, or static cling if you want a removable option.

Choosing Your Size and Placement

Measure your intended spot before ordering, because the width you select is the width of the shark at its widest point. A 12-inch pair suits coolers, bait boxes, towables and smaller jon boats. The 18 to 24-inch range fits most transoms, leaning posts and console sides. For bay boats, offshore rigs and pontoon fencing, the 36 and 48-inch sizes make a strong statement visible from another boat or the dock. When placing two decals on opposite sides of the hull, keep them at the same height and distance from the bow so the boat reads symmetrically on the water. Flat or gently curved surfaces give the cleanest result.

Applying Your Shark Decals on the Water or at the Dock

Application takes a few minutes with basic care. Clean the surface with isopropyl alcohol and let it dry completely so no wax or salt residue is trapped under the film. Peel the backing, position the shark, and squeegee from the center outward to push air toward the edges, then remove the transfer tape slowly at a low angle. Warm the decal slightly with a hair dryer on curved hull sections to help it conform. Avoid applying in direct sun on a hot deck, since rapid surface heating can affect positioning. Static cling versions press on without adhesive and lift off cleanly, which is handy if you like changing graphics between seasons or move decals between the boat and the truck.

What you get

• Set of 2 matching shark silhouette decals for symmetrical hull placement
• Available in 12, 18, 24, 36 and 48 inch widths
• Die cut to the silhouette outline with no background film
• Finish options: matte, gloss, clear or static cling vinyl
• Cut from cast or calendered vinyl depending on finish selected
• Suitable for hull sides, transoms, coolers, trailers and towables
• Includes transfer tape for aligned, bubble-free application

Specifications

Frequently asked questions

Will these decals hold up to saltwater and washing?

The vinyl is cut for outdoor marine use and can be rinsed with a hose or washed with mild soap. Avoid pressure washing directly at the decal edges, which can lift the film over time.

Can I put one shark on each side of my boat?

Yes. The set includes two identical decals so you can mirror them on port and starboard, stack both on the transom, or use one on the boat and one on a cooler or trailer.

What if I want to remove the decals later?

Warm the decal with a hair dryer and peel it back slowly at a low angle. Any remaining adhesive can be cleaned off with isopropyl alcohol. Static cling finishes remove without adhesive residue.