Skull Car Hood Decal, Racing Stripes Vinyl Set of 2

Description

A set of two skull racing stripes, solvent-printed on outdoor vinyl and offered in widths from 12 to 48 inches. Made for US drivers who want an aggressive racing look on their hood without paint or permanent mods.

A Skull Graphic with a Bold Printed Finish

This set pairs the classic dual-stripe hood layout with a detailed skull graphic rendered in a bold printed finish. The artwork is printed directly onto the vinyl film, so the surface carries a clean, eye-catching look at a glance, without the cost or permanence of paint. Because the artwork is solvent-printed, the detail in the skull holds up both up close and at a distance, which matters on a graphic that lives on the center of a hood. The set includes two matching stripe decals, letting you lay out a symmetric pair across the hood for a balanced, race-ready look aimed squarely at the racing segment: loud, deliberate, and built around a single bold image.

Choosing Your Width: 12 to 48 Inches

The set is offered in widths from 12 inches up to 48 inches, so the same skull stripe design can scale from a narrow accent to a full-width statement across a hood. Smaller widths keep the pair tight and work well on compact hoods or as placement on fenders and quarter panels; mid-range sizes suit typical car hoods; the largest widths are sized for wide hoods, truck panels, and tailgates. Before ordering, measure the area you want the pair to cover, edge to edge, and compare it against the available width options. Both decals in the set are sized to match the width you select, so the pair stays proportional at every size. Measure twice, because a tape measure takes less time than an exchange.

Solvent-Printed Vinyl Built for the Weather

These decals use the standard construction for vehicle graphics: solvent inks printed onto outdoor-grade vinyl film. Solvent printing bonds the ink into the vinyl surface rather than leaving it sitting on top, which is why it is the common choice for decals that face sun, rain, and road grime. The printed effect is part of that ink layer, not a separate coating, so there is nothing to peel or flake away. There is no drilling, no badges, and no repainting involved; the stripes go on with transfer tape like any other vinyl decal and give you a non-permanent way to change the look of a hood. For drivers who like to restyle their ride season to season, that flexibility is the whole point.

Installation: Clean, Align, Squeegee

Application follows the standard transfer-tape method used on most vinyl graphics. Start with a hood that is washed, dried, and free of wax in the area where the stripes will sit. Position each decal before committing, and use the second stripe as a reference to keep the pair even across the hood. Once placement looks right, press from the center outward with a squeegee or a firm card to secure the vinyl and push air toward the edges, then peel the application tape back slowly at a shallow angle. Vinyl is more cooperative in warm conditions; in cold weather, let the decal reach room temperature before starting. The symmetry of the pair is what sells the racing look, so a few extra minutes spent on alignment pays for itself.

What you get

• Set of 2 matching skull stripe decals for a symmetric hood layout
• Available in widths from 12 to 48 inches
• Bold printed finish applied directly onto the vinyl
• Solvent-printed inks on outdoor-grade vinyl film
• Applies with the standard transfer-tape method, no drilling or paint
• Works on smooth exterior surfaces: hoods, fenders, tailgates, toolboxes

Specifications

Frequently asked questions

Is the gloss finish shiny?

Yes. The gloss finish is a smooth, high-shine surface on the vinyl film. Because the shine is part of the film itself, there is no separate coating to peel off.

How do I pick the right width?

Measure the area of the hood you want the pair of stripes to cover, edge to edge, then choose the closest available width. Smaller widths like 12 inches work as accents, while the larger sizes up to 48 inches make a full-width statement.

Will a vinyl decal hurt my paint?

Applied to a clean, fully cured paint surface, a vinyl decal is a non-permanent styling option compared with paint work. Avoid applying over fresh or uncured paint, and keep the surface wax-free where the stripes will sit.